• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Backfiring through intake and cannot check codes

  • Thread starter Thread starter webshot
  • Start date Start date Jul 19, 2008
  • 1
  • 2
  • 3
Next
1 of 3 Next Last
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 19, 2008
#1
  • Jul 19, 2008
  • #1
Backfiring through intake NOW HAVE CODES!! thx JRICHKER

I'll start a new topic that kind of bridges both of my topics together. I am have backfiring and loss of power at WOT and switching gears. Especially 1 to 2nd. I have changed the plugs, wires, cap and rotor. Plus checked the timing. WHat else can I check? As I mentioned I cannot run codes. FOr some reason when I try the CEL just stays on. SO I have 2 problems. Backfiring and not able to run codes. Any help with either problem would be great.

It is a 88GT bone stock, 5 speed.

I searched and read that others said to try cleaning MAF, get a new BAP (dont know that that is) and new TPS. As for the TPS I checked mine and it is at .42 is that ok? MAF I was told that you cannot clean that, and to have a shop do it. Is that true? Any advice is greatly appreciated as I feel my hands are tied by not being able to check codes.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 19, 2008
#2
  • Jul 19, 2008
  • #2
There is no need to have a shop dump the codes, you can do it yourself. Only the 1988 model cars made for Califorina with factory Mass air have a working check engine light. If codes will not dump using the following method, you have wiring problems.

Dump the codes and see what the computer says is wrong…Codes may be present in the computer even if the Check Engine light isn’t on.

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great. You watch the flashing test lamp or Check Engine Light and count the flashes.

See Troublcodes.net Trouble Codes OBD & OBD2 Trouble Codes and Technical info & Tool Store. By BAT Auto Technical





If your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.



89 through 95 cars have a working Check Engine light. Watch it instead of using a test lamp.



Do not jumper anything to the single black connector. It is the power for the under the hood light.

What to expect:
You should get a code 11 (two single flashes in succession). This says that the computer's internal workings are OK, and that the wiring to put the computer into diagnostic mode is good. No code 11 and you have some wiring problems.

Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

Alternate methods:
For those who are intimidated by all the wires & connections, see Actron® for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Wal-Mart.

Or for a nicer scanner see EQUUS DIGITAL FORD CODE READER (3145) – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $30.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 19, 2008
#3
  • Jul 19, 2008
  • #3
hmmm, ok for the wiring problem, is this a situation where I need to drop the dash? I am just not sure where to start to get the CEL working. Also I am thinking that I am not understanding this diagram completely. Is it not the right technique to use a paper clip to go from the black/white wire to the tan wire to invoke the test? Sorry for the bone head question. I am starting to think I am doing something wrong.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 19, 2008
#4
  • Jul 19, 2008
  • #4
Do not mess with the dash or the wiring at this point. There is a way to make the CEL work, but that is not up for discussion at this time.

Simply follow the directions I posted for use with an external test light connected to the self test output (tan wire). The diagnostic connector drawing is exactly like the one in 5.0 Mustangs as they came from the factory.

There is a single gray connector with a red/white wire in the same wiring bundle as the diagnostic connector. That gets jumpered to the black/white wire diagnostic connector. It is the solid red wire in my drawing.

Do not jumper anything to the single black connector. It is the power for the under the hood light. It is in another bundle of wires near the windshield wiper
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 19, 2008
#5
  • Jul 19, 2008
  • #5
OK GREAT!!! It worked. !!! Many many thanks

Now back to the issues. Backfiring under load and loss of power. Already changed, plugs, wires, cap and rotor. TPS voltage is .42.

With engine off I get the following codes
41, 87, 91

With engine running I get the following codes
12, 21, 91

91 is present in both and seems to point to fuel system control.
12 says idle speed control. Is that linked to a bad tps or IAB?
21 not sure where to start on that one.
41 and 87 seems to be something regarding fuel as well.

I have never really messed with the fuel sys. Any tips or where to starts or advice is greatly appreciated.

SHould I start a new topic?
 

justagt

Founding Member
Oct 26, 2000
143
0
0
Jul 19, 2008
#6
  • Jul 19, 2008
  • #6
backfire

Check over all of your vacuum lines very carefully to see if any are cracked or disconnected. Some are hard plastic lines about the size of a small cocktail straw, others are larger and made of rubber.

Do you have a hunting idle at all?

The other thing that you could check is the fuel pressure if you have a fuel pressure gauge.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 19, 2008
#7
  • Jul 19, 2008
  • #7
I do not have a fule pressure gauge. Is this something I can get at autozone? And will it say how to use or install it? Gonna check for vacuum leaks now.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 19, 2008
#8
  • Jul 19, 2008
  • #8
Need Advice

I had a guy take a look at the car today and despite me telling him the symptoms and telling him the codes. He is convinced that my timing chain has too much and that is causing my issues. Does this sound correct? Need advice before I pay this dude 150 to do this for me. I wont be paying if it dont take care of the problem, but just principal. It seems so far off from the codes I am getting
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 19, 2008
#9
  • Jul 19, 2008
  • #9
Code 12 -Idle Air Bypass motor not controlling idle properly (generally idle too low) - IAB dirty or not working. Take it off and clean it thoroughly with throttle body cleaner. Clean the electrical contacts with non flammable brake parts cleaner at the same time.

Code 21 – ECT sensor out of range. Broken or damaged wiring, bad ECT sensor.
Note that that if the outside air temp is below 50 degrees F that the test for the
ECT can be in error.


The ECT sensor has absolutely nothing to do with the temperature gauge. They are
different animals. The ECT sensor is normally located it the RH front of the engine in
the water feed tubes for the heater.

The ACT & ECT have the same thermistor, so the table values are the same

ACT & ECT test data:

Use Pin 46 on the computer for ground for both ECT & ACT to get most accurate
readings.

Pin 7 on the computer - ECT signal in. at 176 degrees F it should be .80 volts

Pin 25 on the computer - ACT signal in. at 50 degrees F it should be 3.5 volts. It is
a good number if the ACT is mounted in the inlet airbox. If it is mounted in the lower
intake manifold, the voltage readings will be lower because of the heat transfer.

Voltages may be measured across the ECT/ACT by probing the connector from
the rear. A pair of safety pins may be helpful in doing this. Use care in doing it
so that you don't damage the wiring or connector.

Here's the table :

50 degrees F = 3.52 v
68 degrees F = 3.02 v
86 degrees F = 2.62 v
104 degrees F = 2.16 v
122 degrees F = 1.72 v
140 degrees F = 1.35 v
158 degrees F = 1.04 v
176 degrees F = .80 v
194 degrees F = .61
212 degrees F = .47 v
230 degrees F = .36 v
248 degrees F = .28 v

Ohms measures at the computer with the computer disconnected, or at the sensor with the sensor disconnected.

50 degrees F = 58.75 K ohms
68 degrees F = 37.30 K ohms
86 degrees F = 27.27 K ohms
104 degrees F = 16.15 K ohms
122 degrees F = 10.97 K ohms
140 degrees F = 7.60 K ohms
158 degrees F = 5.37 K ohms
176 degrees F = 3.84 K ohms
194 degrees F = 2.80 K ohms
212 degrees F = 2.07 K ohms
230 degrees F = 1.55 K ohms
248 degrees F = 1.18 k ohms

Diagram courtesy of Tmoss & Stang&2birds



See the following website for some help from Tmoss (diagram designer) & Stang&2Birds
(website host) for help on 88-95 wiring Mustang FAQ - Engine Information

Ignition switch wiring
http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

Fuel, alternator, A/C and ignition wiring
http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

Complete computer, actuator & sensor wiring diagram for 88-91 Mass Air Mustangs
http://www.veryuseful.com/mustang/tech/engine/images/88-91_5.0_EEC_Wiring_Diagram.gif

Vacuum diagram 89-93 Mustangs
http://www.veryuseful.com/mustang/tech/engine/images/mustangFoxFordVacuumDiagram.jpg

Code 41 or 91 - O2 indicates system lean. Look for a vacuum leak or failing O2 sensor.

Code 41 is a RH side sensor,
code 91 is the LH side sensor.

The computer sees a lean mixture signal coming from the O2 sensors and tries to compensate by adding more fuel. Many times the end result is an engine that runs pig rich and stinks of unburned fuel.

The following is a Quote from Charles O. Probst, Ford fuel Injection & Electronic Engine control:
"When the mixture is lean, the exhaust gas has oxygen, about the same amount as the ambient air. So the sensor will generate less than 400 Millivolts. Remember lean = less voltage.

When the mixture is rich, there's less oxygen in the exhaust than in the ambient air , so voltage is generated between the two sides of the tip. The voltage is greater than 600 millivolts. Remember rich = more voltage.

Here's a tip: the newer the sensor, the more the voltage changes, swinging from as low as 0.1 volt to as much as 0.9 volt. As an oxygen sensor ages, the voltage changes get smaller and slower - the voltage change lags behind the change in exhaust gas oxygen.

Because the oxygen sensor generates its own voltage, never apply voltage and never measure resistance of the sensor circuit. To measure voltage signals, use an analog voltmeter with a high input impedance, at least 10 megohms. Remember, a digital voltmeter will average a changing voltage." End Quote

Testing the O2 sensors
Measuring the O2 sensor voltage at the computer will give you a good idea of how well they are working. You'll have to pull the passenger side kick panel off to gain access to the computer connector. Remove the plastic wiring cover to get to the back side of the wiring. Use a safety pin or paper clip to probe the connections from the rear. The computer pins are 29 (LH O2 with a dark green/pink wire) and 43 (RH O2 with a dark blue/pink wire). Use the ground next to the computer to ground the voltmeter. The O2 sensor voltage should switch between .2-.9 volt at idle.

Note that all resistance tests must be done with power off. Measuring resistance with a circuit powered on will give false readings and possibly damage the meter. Do not attempt to measure the resistance of the O2 sensors, it may damage them.

Testing the O2 sensor wiring harness
Most of the common multimeters have a resistance scale. Be sure the O2 sensors are disconnected and measure the resistance from the O2 sensor body harness to the pins on the computer.

The O2 sensor ground (orange wire with a ring terminal on it) is in the wiring harness for the fuel injection wiring. I grounded mine to one of the intake manifold bolts

Replace the O2 sensors in pairs if replacement is indicated. If one is weak or bad, the other one probably isn't far behind.

If you get only code 41 and have changed the sensor, look for vacuum leaks. This is especially true if you are having idle problems. The small plastic tubing is very brittle after many years of the heating it receives. Replace the tubing and check the PVC and the hoses connected to it.
A secondary problem with only a code 41 is for cars with an intact smog pump and cats. If the tube on the back of the heads clogs up the driver’s side, all the air from the smog pump gets dumped into one side. This excess air upsets the O2 sensor calibration and can set a false code 41. The cure is to remove the crossover tube and thoroughly clean the insides to that there is no carbon blocking the free flow of air to both heads.

Code 87 – fuel pump primary circuit failure. The fuel pump lost power while the engine was running. Check fuel pump relay, check inertia switch, wiring to/from inertia switch, red wire going to inertia switch for +12volts. Check the other side of inertia switch for +12 volts.



To help troubleshoot the 87 code, follow this link for a wiring diagram for 89-93 cars http://www.autozone.com/servlet/UiB..._us/0900823d/80/19/59/5a/0900823d8019595a.jsp

For 79-88 cars use, http://www.autozone.com/servlet/UiB..._us/0900823d/80/16/71/3c/0900823d8016713c.jsp

Be sure to disconnect the battery for about 10 minutes when you replace any sensors or make any adjustments. That will force the computer to adjust to the new sensor readings. Leave the code 87 for last and see if it comes back after you disconnect the battery.
 

justagt

Founding Member
Oct 26, 2000
143
0
0
Jul 19, 2008
#10
  • Jul 19, 2008
  • #10
maybe

webshot said:
Need Advice

I had a guy take a look at the car today and despite me telling him the symptoms and telling him the codes. He is convinced that my timing chain has too much and that is causing my issues. Does this sound correct? Need advice before I pay this dude 150 to do this for me. I wont be paying if it dont take care of the problem, but just principal. It seems so far off from the codes I am getting
Click to expand...

Depends...how many miles are on the car? If it's got less than 100,000 on it, I doubt thats the issue. If it's got a ton of miles...could be I guess, but I still doubt it.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 19, 2008
#11
  • Jul 19, 2008
  • #11
webshot said:
Need Advice

I had a guy take a look at the car today and despite me telling him the symptoms and telling him the codes. He is convinced that my timing chain has too much and that is causing my issues. Does this sound correct? Need advice before I pay this dude 150 to do this for me. I wont be paying if it dont take care of the problem, but just principal. It seems so far off from the codes I am getting
Click to expand...



How can he tell that without pulling the timing cover off?


Besides, that wouldn't cause codes like that.

Just tackle 1 problem at a time. Sounds to me like you may have some faulty o2 sensors and a bad ECT sensor. You gotta run the test again with the car hot and see if the ECT sensor code comes back. If the engine is stone cold this code usually always gets tripped.

Clean the Idle air bypass motor, perform the idle reset procedure, reset the computer and drive the car a bit. Then dump the codes again and see what comes up.

jrichker gave you some really good advice. Follow it
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#12
  • Jul 20, 2008
  • #12
Thanks guys, I am going to try this stuff first thing in the morning. Yea I was shocked when he was able to deduce that as well. Without seeing it. Sounded fishy. Some of that stuff seems kinda higher level. BUt I am going to give it a try. Anyone have a pic of the ECT and the 46 pin connector I am to be testing? Sorry for the baby step questions.

Man you guys are a Godsend. Truly thanks for the help.

Also how do you run the reset idle procedure? Bah maybe I can search for that....thanks folks. Also again, engine has 154k. And just found out car has no thermostat in it. Not sure if that helps or hurts.

edit again. Is the IAB the deal on the side of the TB?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 20, 2008
#13
  • Jul 20, 2008
  • #13
ECT is the sensor that is threaded into the coolant pipe that runs up the passenger side of the motor. A rubber coolant line taps into this pipe and plumbs into the EGR spacer. Locate the pipe and you'll find the sensor. It's the only one in it.

Idle reset procedure is as follows.

Unplug the idle air bypass motor on the throttle body and start the car. There is a screw under the throttle body used to adjust idle. If the engine will ont run with the IAB unplugged, open it up slightly. Once you get the engine running, you want to set minimum idle by adjusting the screw to the point where the car idles..but as low as you'd feel comfortable driving with. You just don't want it to be ont he verge of stalling.

Now disconnect the battery for 15 mins.

Plug IAB back in and reconnect battery. Start the car and it might run kinda lopey. Just let it idle for 2 mins and then turn on all the accessories you can and let it run.

After a few starts and shutoffs it will relearn idle strategy again.


Do this after cleaning the IAB. Disassemble it and really clean the gunk out. It may need to be replaced if it's really bad but usallly it can be saved.

Also take the EGR and clean the gunk out of it as well.

Doing that will also wipe out any codes stored. Give the car some honest time to drive around and then retest and see what comes back.


I bet the other two codes will reappear suggesting time for new o2 sensors as well.

You could also clean the MAF sensor. I assume your car is a cali-based '88 so it has Mass Air? If so, there will be a large aluminum sensor on the air intake track. On top held in place with two secutiry screws is a peice of electronics. CARFEFULLY take this out and clean the wires you'll see with electronics spray available at radio shack. Do not touch the wires. Just spray them and then put the sensor back.

The MAP sensor (or BAP on mass air cars) is the black box mounted dead center on the firewall. It can sometimes go back but you would get a code for it.
 

justagt

Founding Member
Oct 26, 2000
143
0
0
Jul 20, 2008
#14
  • Jul 20, 2008
  • #14
hmm

* E D I T *

I just read you said the car has no tstat !

There is a huge part of your problem right there, the car needs to get up to operating temp to run properly. My car had a 160 deg and a huge aluminum radiator when I bought it ran like complete crap. Would hesitate badly between shifting and wanted to die when taking off from a stop. Put a Motorcraft 195 deg tstat in there before you do anything else. It helped my car greatly.

You are getting an ECT code because your car isn't reaching operating temp because you have no tstat, not because the ECT sensor is bad. Don't even mess with the ECT unless you are still getting a code after you have put a tstat in.

* E D I T *

Mustang5L5 said:
How can he tell that without pulling the timing cover off?


Besides, that wouldn't cause codes like that.

jrichker gave you some really good advice. Follow it
Click to expand...

You can pop off the dist cap and watch the rotor. You take off the serp belt and use a breaker bar to turn the engine over by hand and then see if you can turn the crank pulley without the rotor moving to check for slop in the timing chain. Again, I highly doubt that's the issue and as was mentioned you wouldn't be getting codes.

jrichker gave you some really good advice. Follow it

+1
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#15
  • Jul 20, 2008
  • #15
woohoo, progress I think.

Ok did the following things per suggestions;

Installed Thermostat (Mr. Gasket 195)
Cleaned IAB thoroughly
Cleaned MAF (with MAF cleaner)
Drove car for a good while, got it to running temp (all good on the t-stat)
Came back, ran idle reset procedure (tho my car ran just fine without the IAB plugged in, no setting necessary)
Cleared codes and ran again

With engine off but car at running temp

11

With car on at running temp

94, 44 (Air system inoperable)

Other codes no where to be found. Car still backfires a bit, but not as much as before. And there has been a slight power gain. But these codes sound pretty bad. Any ideas on these? Of course I am goiing to do my own search but any input would be great. I have not tried the other things just yet that Jrichker mentioned (the fuel relay stuff) as it seems to not be an issue anymore I think?

Thanks folks.

FOrgot to add I had been using the cheapo gas. 86 Octane.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#16
  • Jul 20, 2008
  • #16
Ok found this write up from J-Richker on codes 94 44. I am gonna try these things, but when it says "Apply Vacuum" (In the first paragraph it says it a few times). Also it does feel like my car is getting better. But my question is will this final code(s) be causing my backfire issue?
http://forums.stangnet.com/748726-engine-codes-13-44-94-a.html


Codes 44 & 94 - AIR system inoperative - Air Injection. Check vacuum lines for leaks, & cracks. Disconnect the big hose from smog pump: with the engine running you should feel air output. Reconnect the smog pump hose & apply vacuum to the first vacuum controlled valve: Its purpose is to either dump the pump's output to the atmosphere or pass it to the next valve. The next vacuum controlled valve directs the air to either the cylinder heads when the engine is cold or to the catalytic converter when the engine is warm. Disconnect the big hoses from the back side of the vacuum controlled valve and start the engine. Apply vacuum to the valve and see if the airflow changes from one hose to the next.
The two electrical controlled vacuum valves mounted on the rear of the passenger side wheelwell turn the vacuum on & off under computer control. Check to see that both valves have +12 volts on the red wire. Then ground the white/red wire and the first solenoid should open and pass vacuum. Do the same thing to the light green/black wire on the second solenoid and it should open and pass vacuum.

Remember that the computer does not source power for any actuator or relay, but provides the ground necessary to complete the circuit. That means one side of the circuit will always be hot, and the other side will go to ground or below 1 volt as the computer switches on that circuit.

The computer provides the ground to complete the circuit to power the solenoid valve that turns the vacuum on or off. The computer is located under the passenger side kick panel. Remove the kick panel & the cover over the computer wiring connector pins. Check Pin 38 Solenoid valve #1 that provides vacuum to the first Thermactor control valve for a switch from 12-14 volts to 1 volt or less. Do the same with pin 32 solenoid valve #2 that provides vacuum to the second Thermactor control valve. Starting the engine with the computer jumpered to self test mode will cause all the actuators to toggle on and off. If after doing this and you see no switching of the voltage on and off, you can start testing the wiring for shorts to ground and broken wiring. An Ohm check to ground with the computer connector disconnected & the solenoid valves disconnected should show open circuit between the pin 32 and ground and again on pin 38 and ground. In like manner, there should be less than 1 ohm between pin 32 and solenoid valve #2 and pin 38 & Solenoid valve #1.

If after checking the resistance of the wiring & you are sure that there are no wiring faults, start looking at the solenoid valves. If you disconnect them, you can jumper power & ground to them to verify operation. Power & ground supplied should turn on the vacuum flow, remove either one and the vacuum should stop flowing.
See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host)

http://www.veryuseful.com/mustang/te...nks-ign-ac.gif

http://www.veryuseful.com/mustang/te...1eecPinout.gif

See http://forums.stangnet.com/attachmen...6&d=1180923382 for a very nice drawing of the Thermactor Air System (smog pump) plumbing

If you have a catalytic converter H pipe, you need to fix these codes. If you don't, then don't worry about them


Thermactor Air System
Some review of how it works...

The Thermactor air pump (smog pump) supplies air to the heads or catalytic converters. This air helps break down the excess HC (hydrocarbons) and CO (carbon monoxide). The air supplied to the catalytic converters helps create the catalytic reaction that changes the HC & CO into CO2 and water vapor. Catalytic converters on 5.0 Mustangs are designed to use the extra air provided by the smog pump. Without the extra air, the catalytic converters will clog and fail.

The Thermactor air pump draws air from an inlet filter in the front of the pump. The smog pump puts air into the heads when the engine is cold and then into the catalytic converters when it is warm. The Thermactor control valves serve to direct the flow. The first valve, TAB (Thermactor Air Bypass) or AM1 valve) either dumps air to the atmosphere or passes it on to the second valve. The second valve, TAD (Thermactor Air Diverter valve or AM2 valve) directs it to the heads or the catalytic converters. Check valves located after the TAB & TAD solenoids prevent hot exhaust gases from damaging the control valves or pump in case of a backfire. The air serves to help consume any unburned hydrocarbons by supplying extra oxygen to the catalytic process. The computer tells the Thermactor Air System to open the dump valve at WOT (wide open throttle) minimizing engine drag. The dump valve reduces the parasitic drag caused by the smog pump to about 2-4 HP at WOT. The dump valve also opens during deceleration to reduce or prevent backfires.






Computer operation & control for the Thermactor Air System
Automobile computers use current sink technology. They do not source power to any relay, solenoid or actuator like the IAC, fuel pump relay, or fuel injectors. Instead the computer provides a ground path for the positive battery voltage to get back to the battery negative terminal. That flow of power from positive to negative is what provides the energy to make the IAC, fuel pump relay, or fuel injectors work. No ground provided by the computer, then the actuators and relays don't operate.

One side of the any relay/actuator/solenoid in the engine compartment will be connected to a red wire that has 12-14 volts anytime the ignition switch is in the run position. The other side will have 12-14 volts when the relay/actuator/solenoid isn't turned on. Once the computer turns on the clamp side, the voltage on the computer side of the wire will drop down to 1 volt or less.

In order to test the TAD/TAB solenoids, you need to ground the white/red wire on the TAB solenoid or the light green/black wire on the TAD solenoid.

For 94-95 cars: the colors are different. The White/Red wire (TAB control) is White/Orange (Pin 31 on the PCM). The Green/Black wire (TAD control) should be Brown (pin 34 at the PCM). Thanks to HISSIN50 for this tip.

To test the computer, you can use a test light across the TAB or TAD wiring connectors and dump the codes. When you dump the codes, the computer does a self test that toggles every relay/actuator/solenoid on and off. When this happens, the test light will flicker.
Click to expand...
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 20, 2008
#17
  • Jul 20, 2008
  • #17
webshot said:
94, 44 (Air system inoperable)


FOrgot to add I had been using the cheapo gas. 86 Octane.
Click to expand...


Do you have the smog pump removed or bypassed? Those codes are usually typical of that equipment being removed and usually don't affect how the car runs.


You mean 87 octane? beleive it or not, the "cheap" gas is actually the gas with the most energy. With stock 10 degrees of timing and stock compression, the engine will make the most HP with the lowest octane. Octane is just a value of how easily the fuel ignites. Cars with high compression and power adders need the higher octane to prevent detonation.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#18
  • Jul 20, 2008
  • #18
All my smog stuff is there and should be operational. I have to smog this month too. SO this code is not good for me. So do I have a bigger underlying issue with the car since I am still experiencing the backfire through the intake? Though it has went away a bit.
 

justagt

Founding Member
Oct 26, 2000
143
0
0
Jul 20, 2008
#19
  • Jul 20, 2008
  • #19
timing

Another thing to check:

Get a timing light and check your timing with the spout connector out.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 20, 2008
#20
  • Jul 20, 2008
  • #20
webshot said:
All my smog stuff is there and should be operational. I have to smog this month too. SO this code is not good for me. So do I have a bigger underlying issue with the car since I am still experiencing the backfire through the intake? Though it has went away a bit.
Click to expand...


Well perhaps the two codes are related.

Check your vacuum lines on the pass side of the motor. You should see some 1" diameter rubber hose running from the smog pump to the rear of the engine. There will be two solenoids in line with hard plastic vac lines on top. Make sure one of these lines are cracked and broken. Trace them back to the firewall and verify everything is plugged in.

These lines are hard plastic and commonly crack and leak.
 
  • 1
  • 2
  • 3
Next
1 of 3 Next Last
You must log in or register to reply here.

Similar threads

1
Engine 91 mustang 302 Low acceleration car backfires pops and acts like it doesn’t want to take fuel
  • 1991Fox5.0
  • Oct 4, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
1991Fox5.0
1
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
516
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
G
Idle surging after warm up
  • GALLY3309
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
253
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 10, 2026
Noobz347
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
613
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
P
Progress Thread New To Me 1988 GT - trying to set up vacuum lines for upper intake question
  • pindude80
  • May 6, 2025
  • Fox 5.0 Mustang Tech
  • 9 10 11
Replies
214
Views
16K
Fox 5.0 Mustang Tech Mar 28, 2026
pindude80
P
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?