• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Backfiring through intake and cannot check codes

  • Thread starter Thread starter webshot
  • Start date Start date Jul 19, 2008
Prev
  • 1
  • 2
  • 3
Next
First Prev 2 of 3 Next Last
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#21
  • Jul 20, 2008
  • #21
justagt said:
Another thing to check:

Get a timing light and check your timing with the spout connector out.
Click to expand...

I have been reading up on timing and I still do not understand what to look for. I do not see any marks. I do see the 2 guides (for lack of a better word). But no marks on the balancer to judge by.

GOnna check for vacuum leaks now.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 20, 2008
#22
  • Jul 20, 2008
  • #22
Get some sandpaper and sand the balancer and you will see them. They sometimes rust over. Take a permanent marker and mark 10 degrees and you'll see it when you shine the timing light down at it
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#23
  • Jul 20, 2008
  • #23
Ok update. Checked for vacuum leaks. I have none. Tried the things in Jrichkers post and everything came back ok. I checked my timing. Right now it is about 12, when I set it back to 10 the car got real rough and though it held idle. But sounded better @12. The car still has a very noticeable miss. And backfires through the intake occassionally. Though the changes thus far has the car running a lot better. Not sure if that is a viable solution (setting the timing to 12) but it helps.

I am open to anymore suggestions. Thanks for the help.

Also codes are still the same.

Edit
I am leaning towards something actually being wrong with the engine now . COuld be my paranoia setting in tho
 

justagt

Founding Member
Oct 26, 2000
143
0
0
Jul 20, 2008
#24
  • Jul 20, 2008
  • #24
good

12 should be fine. My car seems to run best at 14 even with 87 gas. Every car is alittle different.

You said you changed the plugs. How did the old ones look as far as the coloring of most of them? Did they all look similar or was one especially white or especially black?
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#25
  • Jul 20, 2008
  • #25
They pretty much looked all the same. Some were gapped really high. Like 60 or 70. I still have the old plugs. If it will help I can take a picture of them...lol. But yeah nothing crazy looking about the except they have been in the forever it looks like.

After the first round of changes (IAB and stuff) I noticed the biggest change towards the good side of things. I may just spring the 60 bucks and get a new IAB.

Anymore ideas?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 20, 2008
#26
  • Jul 20, 2008
  • #26
What plugs did you put in and what did you gap them at?

When was the last time you did a complete tune up? Things like cap rotors wires, fuel filter?
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#27
  • Jul 20, 2008
  • #27
Ford Motorcraft spark plugs
Part number SP - 450 ASF42c

I gapped them to .54

I did everything in the last couple of days. Matter of fact I changed the cap and rotor again today. Oh and I checked to make sure the firing order is right
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 20, 2008
#28
  • Jul 20, 2008
  • #28
Back to the TPS. You said it was .42?

It should be around .9-.99. It's not critical that it is here, but .42 seems slightly low
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#29
  • Jul 20, 2008
  • #29
Yea I read somewhere .6 - 1.1 but yea. I tried to adjust it using one of jrichkers guides, but could not get it to go above .42. You think that would cause my issue? I feel like I am running out of rope here...lol. I hope my engine isn't shot to heck.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 20, 2008
#30
  • Jul 20, 2008
  • #30
Your engine runs...it's not shot.


What wires are you checking voltage with?
 

justagt

Founding Member
Oct 26, 2000
143
0
0
Jul 20, 2008
#31
  • Jul 20, 2008
  • #31
FP

I think you need to check your fuel pressure. If your regulator is bad and your fuel pressure is low you could be lean and that would cause backfires through the intake.

Pickup a fuel pressure gauge or have this mechanic guy check it for you. Shouldn't take him 2 minutes. Make sure to check it with the engine at operating temp with the vac line off and thumb over the end of the vac line.

Your TPS voltage is not ideal either...
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 20, 2008
#32
  • Jul 20, 2008
  • #32
Fuel Pressure sounds like a complete new topic...lol. I will revisit jrichkers post about fuel pressure and inertia switches and all that. I thought since I got rid of those codes fuel issues were behind me.

Yea I may replace the tps as well. btw I am using the orange wire and the green and white one. I think I read about the process in jrichkers post.

You think fuel pressure can be checked by a rookie such as myself?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 21, 2008
#33
  • Jul 21, 2008
  • #33
Check fuel pressure – remove the cap from the Schrader valve behind the alternator and connect fuel pressure test gauge
to Schrader valve. The fuel pressure regulator is located on the passenger side of the car behind the throttle body.
Disconnect the small vacuum line from the fuel pressure regulator and plug the line. Leave the port where you removed the
line uncapped and open to the atmosphere.

Start the car and observe the pressure: you should see 37-41 PSI at idle.

Be sure to unplug and reconnect the vacuum line to the fuel pressure regulator when you have finished your tests.

Fuel pressure test gauge are available for rent/loan at most major auto parts stores like AutoZone.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Jul 21, 2008
#34
  • Jul 21, 2008
  • #34
Thanks gonna look into getting the pressure gauge on my way home from work. Will update!
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Jul 21, 2008
#35
  • Jul 21, 2008
  • #35
you are chipping away at it. Don't give up.


As for the TPS, you used the wrong wires. The orange wire will always have .5V on it.

The black wire is your ground and the green is the signal wire.

So test between the black and green wire. You want it in the .6-1.0 range. Most people try to set it at .95 V although it's not critical since the EEC takes a zero reading every time you start the car.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Aug 24, 2008
#36
  • Aug 24, 2008
  • #36
Sorry to dig this old topic up but Ihad not touched the car in weeks. But it turns out my fuel pressure seems to be extremely low. I tested it and this is the findings.

Key on = 11psi

Car running = 19 psi

Way off from the 30-45 psi my Chiltons and recommendations here suggest. My question is now.

Will replacing the FPR suffice or do I have to do the fuel pump too?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 25, 2008
#37
  • Aug 25, 2008
  • #37
Fuel pump pressure test
Disconnect the larger of the two fuel lines up by the Schrader valve. It is the return line and does not
have the Schrader valve on it. Find a piece of rubber fuel hose and clamp it on the return line
coming from the regulator. Stick a bolt in the other end of the hose and clamp it. Make sure that
all your connections are tight and leak proof as possible. Be extremely careful that your
test connections have no leaks. There is a definite fire hazard when you do this test.

When this powers up, you don't want fuel squirting everywhere.
Hook up the fuel pressure test gauge to the Schrader valve pressure test port.

Turn the ignition switch on and watch for leaks. You may want to use a helper inside the car
to cut the switch off quickly if you have a leak. To trick the fuel pump into running, find the ECC test
connector and jump the connector in the Upper RH corner to ground.
.
Caution!!! You have blocked the return line for the fuel pump! Pressure will rise very quickly past safe levels with a good pump

If the pressure goes up past 55 PSI, the pump is good and the fuel pressure regulator is bad.
If the fuel pressure does not hit 55PSI or more in a few seconds, the pump is bad or you have electrical problems.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Aug 25, 2008
#38
  • Aug 25, 2008
  • #38
Hmmm...seems easy enough to try. The thing that scares me is the "or" you threw in there. "Ors" scare me.

Again thanks guys for walking me through this. I will report back my findings.
 
W

webshot

Member
Sep 11, 2005
738
0
17
Yay Area, California
Aug 30, 2008
#39
  • Aug 30, 2008
  • #39
Ok was about to do the test, and I see the return line. What I dont know is where to make the disconnect. I see where the metal becomes rubber towards the bottom of the car. DO I disconnect there? Or do I undo the little fitting that is up by the intake?

Want to make sure I am doing this the safest and correct place. Hopefully someone responds soon
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 30, 2008
#40
  • Aug 30, 2008
  • #40
Look in the A/C repair section for the fuel line tools. They look like little plastic top hats. You will need the 1/2" & 5/8" ones.
The hat shaped section goes on facing the large part of the coupling. Then you press hard on the brim until it forces the
sleeve into the coupling and releases the spring. You may need someone to pull on the line while you press on the coupling.
Put some motor oil on them when you put the line back together.

See
LISLE AIR CONDITIONING/FUEL LINE DISCONNECT TOOL SET (37000) for more information

 
Prev
  • 1
  • 2
  • 3
Next
First Prev 2 of 3 Next Last
You must log in or register to reply here.

Similar threads

1
Engine 91 mustang 302 Low acceleration car backfires pops and acts like it doesn’t want to take fuel
  • 1991Fox5.0
  • Oct 4, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
1991Fox5.0
1
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
516
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
G
Idle surging after warm up
  • GALLY3309
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
253
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 10, 2026
Noobz347
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
613
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
P
Progress Thread New To Me 1988 GT - trying to set up vacuum lines for upper intake question
  • pindude80
  • May 6, 2025
  • Fox 5.0 Mustang Tech
  • 9 10 11
Replies
214
Views
16K
Fox 5.0 Mustang Tech Mar 28, 2026
pindude80
P
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?