• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

bbk header fitment prob.

  • Thread starter Thread starter notguilty411
  • Start date Start date Jul 20, 2006
N

notguilty411

New Member
Apr 27, 2005
21
0
1
Jul 20, 2006
#1
  • Jul 20, 2006
  • #1
went out and figured id try and install a set of bbk unequals i picked up from a friend for $5. and i cant get the passenger side to line up for anything. did anyone else have any problems with these same headers? i thought bbk was pretty good as far as fitment went?? so yeah can anyone give me any suggestions as far as getting them on? its starting to piss me off to the point where i want to just throw the stockers back on.
 

1988WHTGT

Member
Mar 31, 2005
270
0
17
Guyton, GA
Jul 20, 2006
#2
  • Jul 20, 2006
  • #2
It took me a while to get mine started
 

payupsucka

Member
Sep 28, 2003
324
0
16
Keeping it grimy in Fall river MA.
Jul 20, 2006
#3
  • Jul 20, 2006
  • #3
most headers once they are used are difficult to line up. i used a pry bar and forced it over
 
N

notguilty411

New Member
Apr 27, 2005
21
0
1
Jul 20, 2006
#4
  • Jul 20, 2006
  • #4
alright ill try that. thanks.
 
D

DeVus1

Founding Member
Mar 29, 2002
400
2
28
P-Town, Va.
Jul 20, 2006
#5
  • Jul 20, 2006
  • #5
It may be easier to install the header, than bolt the H or X pipe to the header. Im not sure which way you are doing it.
 
S

Sicarius428

Active Member
Jan 6, 2004
2,085
5
49
Jul 20, 2006
#6
  • Jul 20, 2006
  • #6
I believe you have the separate flange headers which I have too. Those headers get "use" to the engine they came off are are a pain to put on another. I switched to AL heads and it was a nightmare. It takes a bit of prying. I used a piece of wood so I don't mar too much and on top of that be careful if you have aluminium heads. Don't want to strip any of the bolt holes in the head. Next time they have to come off im getting some one piece flange FMS headers... take that back... can't support ford right now.
Kevin
 
N

notguilty411

New Member
Apr 27, 2005
21
0
1
Jul 20, 2006
#7
  • Jul 20, 2006
  • #7
lol about not being able to support ford.. i work for them and sometimes i think twice about it. but yeah the motor is out of the car at the moment and we have the driver side header on, the passenger we have everything except the one end bolt towards the rear of the motor. its really starting to piss me off... so we'll see if tomorrow morning we can get it in.
 

SeventyMach1

Keep it lubed .... keep it straight .... and keep
Mar 30, 2005
1,940
3
36
North Carolina
Jul 20, 2006
#8
  • Jul 20, 2006
  • #8
IIRC, all BBK headers have a single flange (correct me if I'm wrong). Are you sure they're BBK's?


I have BBK UE headers (single flange) and they were super easy to install. Do your's have individual flange's?
 
M

Mike92GT

Founding Member
Jan 23, 2002
583
0
0
Florida
Jul 21, 2006
#9
  • Jul 21, 2006
  • #9
SeventyMach1 said:
IIRC, all BBK headers have a single flange (correct me if I'm wrong). Are you sure they're BBK's?


I have BBK UE headers (single flange) and they were super easy to install. Do your's have individual flange's?
Click to expand...


The older ones had individual flanges, newer ones are one piece. Not sure when they made the switch though
 
S

Sicarius428

Active Member
Jan 6, 2004
2,085
5
49
Jul 21, 2006
#10
  • Jul 21, 2006
  • #10
I have the older unequals that have individual flanges. I am glad they corrected all the fitment issues later but my headers came with the car.
Kevin
 

Blk91stang

Member
Jan 3, 2003
607
0
16
North Brunswick, NJ
Jul 21, 2006
#11
  • Jul 21, 2006
  • #11
notguilty411 said:
lol about not being able to support ford.. i work for them and sometimes i think twice about it. but yeah the motor is out of the car at the moment and we have the driver side header on, the passenger we have everything except the one end bolt towards the rear of the motor. its really starting to piss me off... so we'll see if tomorrow morning we can get it in.
Click to expand...

If 1 bolt hole doesnt line up, get your drill out and open it up a little bit. It's a single flange so i don't understand how your going to pry it over. If i'm not mistaken it's like 1/4" thick steel. This is all assuming you don't have individual flanges like Mac's.
 
You must log in or register to reply here.

Similar threads

LT header id
  • djj62478
  • Feb 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
194
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 25, 2026
General karthief
D
Exhaust Bbk mid pipe and flowmaster catback fitment issues?
  • dqureshi06
  • Jun 8, 2024
  • Fox 5.0 Mustang Tech
Replies
7
Views
1K
Fox 5.0 Mustang Tech Oct 15, 2024
dqureshi06
D
Exhaust 1 3/4” Long Tubes on a Fox Body AOD – Easiest route?
  • 5.0 Mike
  • Mar 19, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
2K
Fox 5.0 Mustang Tech Mar 21, 2025
5.0 Mike
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
328
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?