brake questions

97gtconv.

Member

Jul 31, 2003

244

0

16

Lock Haven, PA

May 20, 2006

#1

• May 20, 2006

• #1

i changed my calipers with stock ones and when i put them back on and bleed the system the fluid was leaking out of the right rear. wouldn't have noticed but i had a buddy doing the bleeder screw. it comes out at the bleeder screw. i looked at the bottom of the line the square block that the bleeder screw goes into and it has some nicks in it. so i figure that's where it's leaking.

could i get aftermarket S/S brake lines to fix it? if so what do i need? I don't know what to do or what to get. thanks

 

K

Kilgore Trout

Fried or Broiled ?

10 Year Member

Mar 30, 2005

4,749

95

134

May 20, 2006

#2

• May 20, 2006

• #2

Yeah, that is not the bleeder screw it is the banjo bolt if it goes into a square block.

 

97gtconv.

Member

Jul 31, 2003

244

0

16

Lock Haven, PA

May 21, 2006

#3

• May 21, 2006

• #3

what would i have to replace? how do i get off the brake line that connects from the caliper to the main brake line?

 

Nater

New Member

Sep 5, 2003

239

0

0

Maplewood, MN

May 21, 2006

#4

• May 21, 2006

• #4

If you are talking about the square block that the line feeds into the caliper, on each side of it there will be brass crush washers and then the banjo bolt. These washers will need to be replaced when the caliper is replaced since they are crushed when you tighten the bolt down. If they are new, tighten the bolt more. If you reused them, get new ones on there right away.

 

K

Kilgore Trout

Fried or Broiled ?

10 Year Member

Mar 30, 2005

4,749

95

134

May 21, 2006

#5

• May 21, 2006

• #5

Also, remember to plug the brake lines when they are disconnected so air does not get drawn up into then.

 

97gtconv.

Member

Jul 31, 2003

244

0

16

Lock Haven, PA

May 21, 2006

#6

• May 21, 2006

• #6

i tried putting new brass washers on and it still leaks.

 

K

Kilgore Trout

Fried or Broiled ?

10 Year Member

Mar 30, 2005

4,749

95

134

May 21, 2006

#7

• May 21, 2006

• #7

Where exactly is it leaking? Can you post a couple pics?

What about the actual bleeder screw? Is it tight?

Also, if you have painted rims and you have spun brake fluid all over the inside of them you must clean this off or it will damage the paint. Brake fluid is very harmful to paint.

 

97gtconv.

Member

Jul 31, 2003

244

0

16

Lock Haven, PA

May 21, 2006

#8

• May 21, 2006

• #8

the screw tightens but it comes from between the block and the caliper where the brass ring is. the screw tightens well but the block has some nicks in it. i think that's what it is. i don't have a camera.

 

K

Kilgore Trout

Fried or Broiled ?

10 Year Member

Mar 30, 2005

4,749

95

134

May 21, 2006

#9

• May 21, 2006

• #9

I am sorry but yours sounds like a different setup than mine and without pics I do not think I can help you. Someone else will be able to I am sure.