• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

cleaning the block?

  • Thread starter Thread starter kornchild4life
  • Start date Start date May 22, 2006

kornchild4life

New Member
Mar 30, 2005
46
0
0
islip, ny
May 22, 2006
#1
  • May 22, 2006
  • #1
Hey need some advice, I took apart a 302 engine that had the head gasket blow and and the oil/anti-freeze/water all mixed up covered the whole inside of the motor . Could anyone give any suggestions to how to clean up the block, with do it yourself cleaning supplies that wont hurt the block? Or is it something i would want to take to a engine shop and have them do it?
 

Mavrick

Founding Member
Aug 29, 2002
2,264
0
46
Collingwood, ON
May 22, 2006
#2
  • May 22, 2006
  • #2
Varsol works great..
 

87_stang

Member
Dec 12, 2005
131
0
16
Tonganoxie, KS
May 22, 2006
#3
  • May 22, 2006
  • #3
Try oven cleaner. I read an article in mm&ff about using it a while back and I tried it and it worked great. Just be sure to rinse the block and heads thoroughly afterwards and dry it good. Good luck.
 

dragnazz5.0

My "0" key d0esn't w0rk, s0 I have t0 use the zer0
Nov 19, 2005
815
5
18
mooresville, nc
May 22, 2006
#4
  • May 22, 2006
  • #4
after you clean it, either paint it or spray it down with wd40 and cover it with a plastic bag or it will start to rust within 5 minutes. granted its only surface rust and will wash off easily. the best bet to dry it is to use compressed air so that you can blow all the little holes out. if you really want to do it right take all the freeze plugs out also. or just take it to a machine shop and have them clean it and do all the machine work to it.
 

kornchild4life

New Member
Mar 30, 2005
46
0
0
islip, ny
May 22, 2006
#5
  • May 22, 2006
  • #5
Thanks guys, I think im going to call around tomorrow to see how come some place want to clean it out, probably be easier n get it all done.
 
You must log in or register to reply here.

Similar threads

O
Sooty/Oily Front Engine & Pulleys
  • ozenator
  • Jun 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
541
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 22, 2026
Blackhawkxx
D
Paint removal on machined gasket surfaces.
  • Ddyer2868
  • Feb 16, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
393
1965 - 1973 Classic Mustangs -General/Talk- Feb 23, 2026
ctandc
C
B
water pump installation questions
  • B0udreaux
  • Feb 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
38
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 28, 2026
General karthief
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
618
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
My next project , a 428 build!
  • horse sence
  • Jul 29, 2026
  • Classic Mustang Specific Tech
  • 9 10 11
Replies
216
Views
5K
Classic Mustang Specific Tech Yesterday at 6:45 AM
DadLife0724
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?