• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Control Arm Bushings Breaking

  • Thread starter Thread starter 93gtmustang
  • Start date Start date Jun 7, 2007

93gtmustang

10 Year Member
Oct 21, 2006
524
43
49
Jun 7, 2007
#1
  • Jun 7, 2007
  • #1
I have BMR adjustable upper control arms and lowers.
My upper bushings are broke apart at the body connections.
Also the drivers side lower is cracked at the body connection.
What would cause this?
They were put on Jan. of 2006
I drag race this car, but it is not really high power.
Ford Racing GT-40 Crate Motor with a 5 speed.
Thanks
 

93gtmustang

10 Year Member
Oct 21, 2006
524
43
49
Jun 9, 2007
#2
  • Jun 9, 2007
  • #2
I called BMR. They said that you have to use synthetic grease with their polyurethane bushings
Regular grease with eat away at them and cause them to break down.
That's most likely the problem.
I didn't install them so I don't know what kind of grease was used
 

Mr Grim

New Member
Dec 29, 2006
58
0
0
Jun 11, 2007
#3
  • Jun 11, 2007
  • #3
I installed both upper and lower BMR arms and greased them with synthetic about 6 months ago. Now I am and feeling a pop in the left side under hard accelleration and decelleration. I was under the car last week, but didn't see or notice anything out of the ordinary. I also have BMR subframes as well as a Steeda tower brace, so there shouldn't be any popping from body flex. My motor is still near-stock, and shouldn't be shredding suspension parts.....I hope BMR didn't scrimp on the bushings!
 

Shakerhood

20+ Year Stangneter
Oct 28, 2004
3,361
211
114
Ohio
Jun 11, 2007
#4
  • Jun 11, 2007
  • #4
I think its best to save the Money and buy top notch Parts like the ones from Maximum Motorsports.
 

93gtmustang

10 Year Member
Oct 21, 2006
524
43
49
Jun 11, 2007
#5
  • Jun 11, 2007
  • #5
BMR said they did have a defective batch of bushings a while back. Mine were installed Jan. 2006 . The defective batch was just recently. I'm sending my old bushings to them anyways to see if they are defective.
 

93gtmustang

10 Year Member
Oct 21, 2006
524
43
49
Jun 11, 2007
#6
  • Jun 11, 2007
  • #6
Mr Grim,
You said you installed them yourself.
Was it hard, did you do it on a lift or jack stands.
I'd like to save myself some money if I could change the bushing myself.
If you could tell me how you changed them and any other tips on changing the bushing would be greatly apprecited.
Thanks
 

Mr Grim

New Member
Dec 29, 2006
58
0
0
Jun 11, 2007
#7
  • Jun 11, 2007
  • #7
Swapping the new arms for the old was a snap...Just do one at a time.
I put the car on stands, then unweighted the axel with a floor-jack. Just use the jack to help work the arms into position.
The only time consuming part is getting the old rubber bushings out of the rear-end housing. Someone else did mine, but you can either drill them out, or burn them out with a torch....clean up the shells, and pop the new ones in. Be sure to grease them after the install...easy to forget.
Good luck!
 

93gtmustang

10 Year Member
Oct 21, 2006
524
43
49
Jun 16, 2007
#8
  • Jun 16, 2007
  • #8
Does anyone have detailed info on changing upper and lower control arms?
I have BRM uppers and lowers on my car right now.
The bushings are shot. They are the polyurethane type.
I have to take the old bushings out and put the new ones in.
Jacking? Pinion Angle? ( Uppers are adjustable) Take one out at a time?
Getting old bushings out, putting new ones in?
Thanks
 

93gtmustang

10 Year Member
Oct 21, 2006
524
43
49
Jun 20, 2007
#9
  • Jun 20, 2007
  • #9
Just finished putting in the new bushings.
It's hard work using jack stands.
If anyone needs any help with this, I'd be more than happy to give some tips to make it easy.
 
You must log in or register to reply here.

Similar threads

C
Suspension Rear suspension help
  • Clark302
  • Aug 17, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
459
Fox 5.0 Mustang Tech Aug 17, 2025
Clark302
C
New Products From J&M Products - 1979-1998 & 1999-2004 Race/Extreme Duty Rear Lower Control Arms
  • J&M Products
  • Oct 9, 2025
  • Vendor Sponsor Forums
Replies
0
Views
475
Vendor Sponsor Forums Oct 9, 2025
J&M Products
Tightening upper control arm bushings at ride height dilemma… need some help
  • AnthonyA1234
  • Dec 27, 2024
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
51
Views
7K
Fox 5.0 Mustang Tech Feb 27, 2025
General karthief
C
Suspension spherical or urethane upper control arm differential side bushings?
  • colehelm
  • Jul 3, 2024
  • Fox 5.0 Mustang Tech
Replies
11
Views
3K
Fox 5.0 Mustang Tech Jul 6, 2024
manicmechanic007
A
SOLD For Sale: 1993 Ford Mustang Cobra Modified
  • anjteal93
  • Sep 5, 2025
  • Fox Body Mustangs For Sale (1979-93)
Replies
13
Views
2K
Fox Body Mustangs For Sale (1979-93) Oct 26, 2025
Mindseye007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?