• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

could too much oil cause pcv valve to pop off?

  • Thread starter Thread starter lxboy
  • Start date Start date Aug 4, 2005
L

lxboy

Member
Jan 16, 2003
46
0
6
connecticut
Aug 4, 2005
#1
  • Aug 4, 2005
  • #1
hey guys i just bought new stang about a month ago. THe car has alot of goodies including a pro bullet 306 and novi 2k with all the bolt ons. I changed the oil for the first time yesterday. The car has a canton 7 qrt oil pan and common sense would tell me to put in 7 qts of oil. I could have sworn i remembered the guy i brought it from telling me that he put 8 qrts of oil in when he changed it. I thought this sounded weird so i put in seven and the car ran great. Later that night i did a little spirited driving including a 1-4th gear full boost run. Still no problems at all. I decided to add an extra quart of oil in the car because it was bothering me that the guy i bought it from told me to put in eight. Well after puting in the extra quart (now at 8 qrts total) i went for a highway run from third to the top of 4th gear and what to you know poof clouds of smoke from the tail pipes. I pulled over at the nearest spot and there was some oil on the fender wall and around the dip stick. Some friends and i decided the pcv valve had popped off and when i reached back there the hose was disconnected. So i pushed the groment back in and the car drove fine and didnt let out a bit of smoke the rest of the night. I dont think i have a crankcase ventilation problem because the car has been run hard for a while without any blowby except this night right after i added the extra quart. i rechanged the oil and made sure there was exactly seven qrts no more no less and i havnt romped on it since but when i give it a little gas it feels totally fine. My question is does it make sense that the extra quart could have cause some slight blow by or should i look into this a little more carefully. Thanks and sorry for the long post i just wanted to make sure you guys had all the details.
 
L

lxboy

Member
Jan 16, 2003
46
0
6
connecticut
Aug 4, 2005
#2
  • Aug 4, 2005
  • #2
ohh ya and i do have a breather on the passanger side valve cover so again i dont think it has to do with ventilation.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Aug 4, 2005
#3
  • Aug 4, 2005
  • #3
So you run a mix of PCV and a breather? I would run one or the other. If using a PCV set up, a Turbo PCV might help (from a TC, Supra, et al). Or just do the breather method and run a couple of them.

Or at least make sure the PCV grommet and valve fit tight. Old grommets tend to vulcanize, which makes it easy for the valve to pop out.

Good luck.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 4, 2005
#4
  • Aug 4, 2005
  • #4
I have a Canton 7 pt pan and have had similar concerns over the oil level.

Turns out the "7qt pan" is actually a 6qt pan and the filter makes the system 7qt. This is the response I got from Canton.

Many people will say that you can run less than max capacity with these pans to avoid kicking oil up onto the crank, and still not get starvation on accelleration or in the turns. This is because of the baffling of the oil pan itself.

I would say that your oil level was too high. In my experience that is when blowby will result in oil blowing out of the PCV or oil dipstick or gasket the most. It only gets worse when you overfill the oil pan. I can't explain why, but that is what I saw when the wrong rings gave me 20% blowby.

As HISSIN50 said though you should probably use a PCV from a boost application. It has worked for others.
 
L

lxboy

Member
Jan 16, 2003
46
0
6
connecticut
Aug 4, 2005
#5
  • Aug 4, 2005
  • #5
thanks alot guys guess i just gotta recheck everything and then suck it up and nail it again and see what happens
 
You must log in or register to reply here.

Similar threads

S
Engine Stalls when downshifting/coasting
  • Scott_S
  • Nov 5, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
740
Fox 5.0 Mustang Tech Nov 6, 2025
Mustang5L5
Fox Ideas for Theft Deterrence in Storage
  • Clutchfork
  • Nov 6, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
38
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Dec 1, 2025
91AOD5.0LX
A
2001 Mustang GT, scorched metal smell and noise from trans/diff?
  • AndyE2255
  • Dec 1, 2025
  • SN95 4.6L Mustang Tech
Replies
4
Views
469
SN95 4.6L Mustang Tech Dec 28, 2025
gkomo
3
Eight inches is enough for me...
  • 351MooseStang
  • Nov 27, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
5
Views
588
1974 - 1978 Mustang II Talk & Tech Mar 2, 2026
Bullitt347
M
Progress Thread mnky99 2001 V6 evap core, ac compressor, heater core replacement
  • mnky99
  • Sep 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
522
1996 - 2004 SN95 Mustang -General/Talk- Sep 5, 2025
mnky99
M
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?