DCC users..I'm having problems...

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
First of all, this is not intended to bash DCC at all as I'm sure it's a wonderful product since there are so many people using them; that is, after all, why I bought one.

I've got it all wired up except the wires for the a/c (just trying to get it to work properly now and don't intend to use the A/C for at least 6 months anyway). I also haven't installed the light yet to show if the fan is on.

Let me say that I wouldn't even have ditched the stock setup as it was working fine for me, except that after my car got wrecked, it was hard to match the fan/shroud up and I also had some overheating problems - before the car was stolen/wrecked, everything was cool (pun intended:D ).

Anyway, I've tried putting the sensor in various positons on the RIGHT side of the radiator if you're standing in front of the car. I've tried putting it as close to the outlet as I can get it, I've tried putting it close to the side, but up a few inches, yada yada. It comes on occassionally, but it only stayed on for like 30 sec yesterday when I pulled over to see if it would run. I believe there's a 180 t-stat in the car since I used a turkey themometer to check temp of coolant after it started to flow across the radiator and it was 180*. I've had the fan set to to come on at 202, 194, and now 180 and it just never seems to come on. The instructions say the unit is set up for a 180* thermo. So, does it come on at 180* - if so, what temp does it go off at? I pulled the sensor and stuck it in the radiator and let some coolant run over it and the fan turned on and stayed on as long as there was warm/hot coolant flowing over it.

Anyone have a pic of exactly where they put their sensor?

I'm considering just hard wiring the fan and using a toggle for now; if I can't get this thing to work pretty soon, that's probably what I'll do. The DCC may end up on ebay:(
 
i can only think of putting the sensor over on the inlet side of the radiator(top hose). i have the thermostat housing sensor so i can't help too much. if you do think about selling it, lemme know what model it is and a price as i need another one to control my water pump.
 
If you have this temp sensor.
temprobe.webp

Then you should mount it somewhere like this.
 

Attachments

  • temprobe.webp
    temprobe.webp
    8.6 KB · Views: 165
If the fan runs with the sensor in the coolant and not with the sensor in the fins, then the sensor isn’t being heated where you have it mounted. There are a number of possibilities:

1) The sensor is mounted in the front of the radiator, which will throw the temperature off by about 20 degrees

2) The sensor is pushed too far into the fins. You’ll find a ridge at the back of the sensor that should rest against the radiator fins. If the sensor is pushed in past that ridge, the ridge will separate the fins from the remainder of the sensor, resulting in a poor thermal contact

3) The controller is set to keep the car at 180, but the thermostat is higher than 180, what will happen is that the fan will cool the water below the thermostat temperature, which will close the thermostat. The tstat then will continuously cycle opened and closed and the controller will follow with the same cycling. Measuring the temperature at the cap (radiator outlet) isn’t accurate. Measure the ECT voltage instead

temp voltage

180 .660
190 .615
200 .530

4) The fins where the sensor is mounted are clogged, if there isn’t any water flow where the sensor is mounted, it won’t measure the temperature accurately. The debris usually ends up in the bottom of the radiator, so you can resolve that problem by sensing at the top of the radiator.
 
The material on the ouside is heat sensitive in that the epoxy liquifies at the running temperature so that it forms to the fins. If you remove it and reinstall it while it's hot, the sleeve will form to some odd shape. You can probably get it hot enough with a hair dryer to reform it over the sensor. It's not critical, as long as it can provide an interface between the sensor and fins. If it looks like it's pretty well totaled, I can send you a new sleeve to replace it
 
Just out of curiosity, when you had it in the radiator, how do you know it wasn't coming on at the right temperature? Just because the upper hose is warm doesn't mean the hot coolant has made it all the way to the outlet (bottom) of the radiator yet, so is it possible the coolant wasn't hot enough to trigger it?

I've never seen my fan come on at exactly the point where my upper hose gets warm, it waits til the sensor senses whatever the temperature you set is, and that's not going to be at the exact second the t-stat opens.
 
The best thing that can be done is to install the light. WIthout it, you really have no clue as to what the DCC is doing. That little light has helped me with a lot of troubleshooting on my electric fan setup. It makes life easier on this mod. I also have the remote temp adjuster installed in my car which also makes troubleshooting and adjusting easier.
 
sgarlic: Well, not only does the car stock gauge read higher than normal (I know they're supposed to be crappy, and I have autometers in the GT, but this gauge read lower before). I will take a reading at the ECT like baskin suggested. I had the turkey thermo in the rad. neck watching temps and it would go past 180 and the fan wouldn't even come close to kicking on, yet it did when I had the sensor in the neck.

I think my problem is that the radiator is probably stock from my 91 GT, the first 1/2 inch by the side of the rad. doesn't have fins and a lot of them are smashed anyway, so it's hard to get the sensor in there real well. I'll have to get the light hooked up and play around w/ the sensor some more. I might decrease the temp to which i comes on to like 166 and see if it'll come on then; of course that would just be a test.

I'll post sometime this week w/ results...thanks for the help.
 
My '93 tbird gives live data and it was running 190* on the scanner today with the fan just turning slow and shutting off. I also just installed bbk underdrive pullies with a new frpp water pump. Revving the motor didn't help lower the temp much. The t-stat is 180*.

I think I will have a pipe fitting tig welded in and epoxy the sensor into another fitting to get a more direct reading. Not too worried about it 'til the motor comes out.
 
The controller doesn’t get any information other than what it measures at the sensor, and the only thing that will make the controller cycle up and down is the thermostat opening and closing, which starts and stops the water flow. If you leave the radiator cap off and start the car, you’ll probably be able to see the water flow cycle with the fan,

The sensor on the controller is +/- 3 degrees, but I’ve seen thermostats as far off as 15 degrees, like just about everything else you buy these days, most are made in china and the quality is pretty low. Putting the sensor into a fitting won’t help, in fact the controller will respond even faster which will result in a higher peak to peak cycle of the fan.
 
tmoss said:
Excellent stuff Brian - If you have not, you should put this type of trouble shooting info on the website.
I have not poked around on his site in quite some time but that is a great idea Tom.

Cool.
 
Alright guys, I skipped school today to play w/ the car :D

I got my light hooked up and it seems to come on when the fan is on, so I guess I'm in good shape...just have it duct taped to the dash for now though lol.

Anyway, I started the car and watched the fan cycle on and off measuring voltages at the ECT and writing them down. Here are a few:

on .52, off .53;
on .50, off .51;
on .53, off .49;
on .45, off .51;
on .48, off .44;
on .43, off .50
on .47, off .45

I watched it for about 10 minutes or so and wrote those few down - didn't get all of them.

So, from the looks of it, it's coming on at 200*. I have it set up w/ the base configuration - no jumpers. I used the hair dryer on the end and got the cover thing molded back around and shoved it into the fins up until I got the thick line in.

I think I'll pull the cap and watch the water move through the radiator while monitoring ECT voltage so see if I can figure out the temp thermostat I have. Seems like my stock gauge is pretty much right on too...the line above the middle line is around 230 and it was sitting right below that... .44v is right around 225* or so.

So I said all of that to ask this:

What should I do? The fan is a 3.8L v6 taurus fan wired up to the high speed. Should I drop my temp on the DCC to 166?
 
ok, well I went back out. The 'stat seems to be opening around stock 195ish. Had the cap off (raised the front drivers side too) and changed the jumpers to 173* (6/8) & (7/9) Results were awesome w/ the cap off:

on .55, off .60
on .52, off .58 (went on up to .63)
on .50, off .62
on .54, off .58 (went on up to .62)
on .51, off .59 (went on up to .63)
on .49, off .57 (went on up to .61)
on .54, off .57 (went on up to .62)
on .49, off .58 (went on up to .60)
on .52, off .57 (went on up to .61 - took about 20 sec though)
on .55, off .57 (went on up to .62)

The coolant was about 6" from the top, but would rise every once in a while. Put the cap on and within 5 sec, the voltages dropped to:

on .49, off .42
on .36, off .39 (went on up to .44)
on .40, off .38 (went on up to .40)
on .35, off .39 (went on up to .42)

So...basically it went from coming on around 200* and getting the car to 194ish within 10-15 sec to coming on at like 230* and getting the car to like 225*.

What's up w/ that?
 
When you put the sensor in the coolent and the fan was running, what was the temperature on the gauge?

EDIT I missed your last post, so disregard, that, I can't see any way pressurizing it would effect the sensor, I don't see how it would effect the thermo either, but the thermostat is definitely way off, so you're not going to be able to hit 180 with it
 
Well, I think the thermostat is probably the stock 195*. I couldn't remember before, but this, and the fact that I can't see any reason why I would go 180* on the LX, makes me believe the thermostat is pretty much right on.

I was just out playing some more and the car got real hot down to low .4x's and even .28v at one point, which made me decide to turn it off. The fan wasn't on (no idea why it wasn't) and I turned the car off...the INSTANT I turned the car off, the fan kicked on and ran for probably 2-3 minutes. Why would it not turn on when the car is running, but when I turn the car off, it immediately turns on?

I feel like I've learned a few things during this process and it's been fun, but I really have no clue how to fix this...if I only I could drive it w/ the cap off and the front drivers side jacked up:lol:

Since the GT is put away for now and won't be out for 6 months, I'm thinking about pulling the 3-core radiator out of it and maybe even the autometer gauges and putting them in the LX. The radiator in the LX (the car the DCC is in) is a 2-core probably stock radiator. Really don't want to go through the work of installing the gauges again, but it would make me feel better knowing I had my autometer mechanical temp gauge monitoring my 5.0.

EDIT: Can't remember if the flow cycle was the same as the fan, but I'd assume so when the cap was off...cap on, probably not...it was like night and day cap off and on.
 
I think may have I just figured it out, the valve in the cap is bi-directional. 17psi pressure, -1 psi vacuum, If the cap is bad, the coolant will contract and collapse the bottom hose when the fan comes on. Try switching the cap