Exhaust Smell

General karthief · Dec 15, 2016

Naw, 19 and matching maf good to go

General karthief · Dec 15, 2016

madmike1157 said:
What,....how did you get the 2.5" pipe jammed into that poor cat? Didn't that create a smell of it's own?

Ohh the humanity....

Used 24 pound injectors
It only smells at the backend

JD1964 · Dec 15, 2016

billison said:
What would the better move be if these are not fancy stock ones, get a maf that matches or get some stocks? I know I gotta pull one to confirm what they are.

But stock heads, cobra intake, b cam, probably don't need 24's

If you need to replace injectors, I recommend the Bosch upgrades from here.

https://fuelinjectorconnection.com/collections/ford-car-rebuilt-injectors

Mustang5L5 · Dec 16, 2016

Did you run your engine running codes yet? Curious to if you got any O2 (rich/lean) codes from that?

I'd find some 19's and put them in, set those aside for later mods.

billison · Dec 16, 2016

Ok, codes pulled.

Let get to full running temp

Koeo
15
82
85

Stored codes
33 Canister or EGR valve not operating properly ( will the charcoal canister do this?)

96 fuel pump circuit -- no clue

Koer
4--- 8 cylinders right?
94 secondary air system--- no clue
44 air management system-- no smog pump?
33

Balance test
9----- pass right?

billison · Dec 16, 2016

Deleted the other thread as it's all the same topic at this point.

Mustang5L5 · Dec 16, 2016

33 is EGR. IS yours there or was it removed? or unplugged?

Ignore code 96. Usually this is common on mass air swapped 86-88's that didn't have a wire run to the fuel pump relay under the seat. If you want to eliminate this code, just need to run 1 wire from ecu to relay.

44/94 is from not having an smog pump setup

Code 82 is smog pump related, and 85 is charcoal canister

Code 15 is keep alive memory for the ecu. If you run the codes after disconnecting the battery you get this. Clear the codes, run again, and it should be gone. If not, you'll need to do some troubleshooting here

billison · Dec 16, 2016

My egr is there. I suspect it may be a vac leak.

Mustang5L5 · Dec 16, 2016

Are all those solenoids on the pass side behind the strut tower still there?

billison · Dec 16, 2016

Yup, but the vac lines were a mess last I checked. My guess is the problem is there.

billison · Dec 16, 2016

Amazon product ASIN B0092U5D3IView: https://www.amazon.com/Lucas-01D062B-Injector-Brand-Chevrolet/dp/B0092U5D3I

Found the injectors. They seem to be right.

Looks like my points of focus will be the egr and charcoal canister

General karthief · Dec 16, 2016

billison said:
Amazon product ASIN B0092U5D3IView: https://www.amazon.com/Lucas-01D062B-Injector-Brand-Chevrolet/dp/B0092U5D3I

Found the injectors. They seem to be right.

Looks like my points of focus will be the egr and charcoal canister

Thats pretty pricey for one injector, what would be wrong with motorcraft brand?

billison · Dec 16, 2016

karthief said:
Thats pretty pricey for one injector, what would be wrong with motorcraft brand?

No clue, but those are what's in there now. I looked up the part number and found they are 19's

Rjaaaaaa · Dec 19, 2016

bird_dog0347 said:
@madmike1157 I'm sure the Cat will get very hot, but doubt it will be hotter than the turbo! You could look for some heat shielding like they put between the floor and cats on the newer mustangs and use that?

like this.

that's a clean install there, don't see any cats ?

billison · Dec 19, 2016

Had another member ask about the cats.

Link to the install thread below. Post 33

http://www.stangnet.com/mustang-forums/threads/bird_dog0347s-fox-has-the-squirts.869954/page-2

billison · Jan 14, 2017

Went to check for power to pin 1.

Found this. Please advice.

JD1964 · Jan 14, 2017

Lots of discussion about it out there. It doesn't appear to do anything other then bump the ignition timing up. Thats something you can do by rotating the distributor. The consensus appears that people are not too impressed with the Hypertech for the Foxbody.

https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=hypertech chip foxbody

JD1964 · Jan 14, 2017

Maybe try removing it and resetting initial timing to 12

billison · Jan 14, 2017

I pulled it and it seems to run smoother without.

About to re pull codes and see what I get.

billison · Jan 14, 2017

Ok. Any clue what computer this is?

Exhaust Smell

wonder how much it would cost to ship you a pair

Sponsors (?)

wonder how much it would cost to ship you a pair

there is enough sticking out to grab on to

That is…until I whipped out my Bissell

I like tinted tail

I like tinted tail

That is…until I whipped out my Bissell

I like tinted tail

That is…until I whipped out my Bissell

I like tinted tail

I like tinted tail

wonder how much it would cost to ship you a pair

I like tinted tail

Well-Known Member

I like tinted tail

I like tinted tail

Attachments

there is enough sticking out to grab on to

there is enough sticking out to grab on to

I like tinted tail

I like tinted tail

Attachments

Similar threads

Privacy & Transparency

Privacy & Transparency