guys cams or not?

ADRENLN

Active Member
Apr 16, 2003
2,342
3
49
NJ
i thought i asked this already, but cant find the thread. anyway this is what im looking for

emissions friendly = stage 1

blower in future = stage 1 blower cams

i need to know everything you guys know about cams!!!!!!! i will hopefully be making this move withen a month.

im still not 100% decided on them yet. i need to know more.

will cams mess up my drivability? do cams mess with compression? i dont want anything raising my compression.

afer install im relying on mph mail order chip till i can get to the dyno, do you think this will be ok?

can performance cams do any damage to the engine or the reliability?

thanks
 
Well unfortunatly VT does not sell a stg 1 blower cam, only stg 2. I really dont know i that will pass, and they will DEFINATLY know it has a cam, even with the stg 1 N/A cam. With a blower, their N/A cam will prolly make lee power than you stock cams due to it having a 110LCA. Blower cams need to be around 114-115LCA. (ie BCs need less overlap) IMO from what I have heard(listening to idle), stg 2s seem to mess up drivability because it will prolly be jerking in 1st gear near idle, and B. the stg 2s will loose lowerend HP and should loose some gas milage. I am going VT stg 1s for those reasons (or to avoid them i mean). stg 1s loose 0 lowend power and dont have too bad of an idle. But ill be getting TTs in early 07, so the cams may have to go....but thats OK, ill live it up for right now (33+RWHP for $545 for about 2 years...works for me). :D No compression raises with cams. If I were you, I would restrain myself from getting on it until you atleast get a dyno run to see where you stand. But knowing how Tim tunes, you will prolly be safe. And yes, if the tune is WAY off and your lean, you could knock a hole in your piston, like I am in danger of right now LOL. Havnt hit it in like 2-3 weeks....MAN its SO hard to just baby it...I can almost see all that carbon building on the top of the cylinder walls and valves. LOL
 
thanks for all the info. doesnt someone have a low end street cam thet will work with a blower. what about comp cams, do they have like a stage 1 blower cam?
 
Check with Houston Performance they have a good all around cam shaft for NA and charged. My buddy put it on his 97 with PI's and got 30 rwhp. They also put it on a charged car and i think they got got 65 rwhp. And yes his does pass inspection
 
If your planning on getting a blower in the future get a blower cam now. Even though your not running the blower now, you'll see good gains NA and when you do get the blower you will see even better gains. Cams will not raise compression, but i would reccomend you get some excellent head gaskets like those from Cometic, with about a .042" thickness. Seal up the heads very well; I've never had a problem with them on my setup.

As far as emissions go, I'm not sure if a stage 2 blower cam would mess with them. I got a stage 3 cam, with a rich tune right now (I had to run stock MAF because my POS Pro-M Univer would never work; running an SCT MAF now :hail2:) so I think your emissions would be heavily controlled by the type of tune you have.
 
ADRENLN said:
thanks for all the info. doesnt someone have a low end street cam thet will work with a blower. what about comp cams, do they have like a stage 1 blower cam?



you can use the vt stage 1 with a blower. i'm putting on a novi 2000 in a couple weeks & i'm keeping my stage 1's in until i get a built motor. just for a reference point; Mdvaldosta over on MPH ran an 11.4 with those cams & his blower on his stock block :nice:

no compression difference

MPH will do just fine

the cams can't damage anything (assuming stage 1) unless you rev it too high

& here's a sound clip for you if you're wondering what they sound like (mods in my garage)
clicky
 
hey theres only one way this can go, vt either makes a stage 1 blower cam or not.

or are you guys saying that they dont make one, but their na stage 1 works well with blower anyway?
 
also i want good head gaskets, cause im doing foxlake ported heads too. well i might end up doing just heads, if the cams turn out to be too much trouble.

anyway i made a thread about strong head gaskets, but got no responces. :shrug: wont thicker head gaskets up the compression. im just trying to keep compression stock for when the blower comes. so i need head gaskets that are same as stock compression, but stronger and well made.
 
cams are something i would like to do in the future also, need to save some $$$ first. Does anybody know what kind of average install costs are to have a shop put them in. I guess, I dont even know how far in the cams are, is it a complete tear down or are they somewhere near the top?
 
ADRENLN said:
also i want good head gaskets, cause im doing foxlake ported heads too. well i might end up doing just heads, if the cams turn out to be too much trouble.

anyway i made a thread about strong head gaskets, but got no responces. :shrug: wont thicker head gaskets up the compression. im just trying to keep compression stock for when the blower comes. so i need head gaskets that are same as stock compression, but stronger and well made.


I believe a thicker head gasket lowers compression where it is the oposite for a thinner one.
 
spederman said:
cams are something i would like to do in the future also, need to save some $$$ first. Does anybody know what kind of average install costs are to have a shop put them in. I guess, I dont even know how far in the cams are, is it a complete tear down or are they somewhere near the top?
the cams are sitting right underneath the valve cover. take off the oil filler cap and you can see one. it's not really hard if you have the right tools and enough time, like a whole afternoon. there is a writeup on modulardepot.com if you want to see what's involved

as for the gasket, 96wn is right, thicker lowers compression, thinner (like metal gaskets) raise compression, not by much though.
 
96WhiteNight said:
I believe a thicker head gasket lowers compression where it is the oposite for a thinner one.



yes you're correct.


& adrenln - i am not sure if they make a stage one blower cam, but the na/cam is mild & therefore isn't toooo detrimental to the blower, so it works. is it the best for it....no, will it work jsut fine.....yes. like i said before that guy got a 11.4 on stock block, vt stage 1 n/a cams & his blower, so they can't be all that bad for it ;)
 
spederman said:
cams are something i would like to do in the future also, need to save some $$$ first. Does anybody know what kind of average install costs are to have a shop put them in. I guess, I dont even know how far in the cams are, is it a complete tear down or are they somewhere near the top?

Modular Powerhouse charges $350 to install cams only and $1000 for cams and valve springs.
 
$350 is a decent price, but mph is also in georgia. that'd be one hell of a drive :nice:



if you have any mechanical experience at all and have the tools (or can borrow some) you should try it yourself.

read this , it seems like alot but most of it is actually getting to the cams (a/c, belts, etc), then putting all the stuff back. not hard, just time consuming
 
hey guys i just got off the phone with ron at fox lake. i am getting their stage 2 heads, but still dont know about the cams. i asked about cams and he said that they would do a custom grind that would be very streetable. however i asked what kind of cams, and he said bullitt or billet i dont know i never heard of them. anyone know what they are? if they are any good.

i assume they are pretty good because if fox lake is using them it must be somwhat quality. i did mention that i will be getting a blower, but im not sure if he understood i want to use it with the cams. i will be calling him back in a couple of weeks.
 
04DarkShadowGT said:
Modular Powerhouse charges $350 to install cams only and $1000 for cams and valve springs.


That's alot cheaper than i thought it would be to install cams, for that price I would rather leave it to the experts than me risking screwing something up. The only downside is that MPH is no where near me. Does anybody know of any sweet places like MPH that deal with all stangs in Texas (preferably Dallas) ?
 
since you guys brought up the subject of the VT stage 1 cams. Here is a question. I'm Also planing on getting them . For the stage 1 as i understood , there is no NEED to change the valve springs. BUT if i did will i see more gains ???
I mean the cams alone will give about 33+ HP , withought the valve springs. So will it be more if i Also changed the valve springs along with the VT stage 1 cams?
 
Quoted from "Scott@VTEngines" as he told me in a PM (he is on MD), "If you're going turbo, and these cams are for that combo, DO NOT use them! I have a turbo grind that is designed for the characteristics a turbo motor prefers. (we made 1600Hp today with a 324 turbo motor). Our n/a cams are ground on a tight centerline, so they have a ton of overlap, which a turbo motor does not like. You need a cam that is intake favored with a wide c/l (115 compared to the 110 the n/a cams are on)." The same applys for blower cams, and even more so. Go ahead, shoot him a PM. Maybe they can make you a custom ground cam that will pass.?.?