• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

heads and compression ratio formula?

  • Thread starter Thread starter importhater5.0
  • Start date Start date Oct 23, 2007
I

importhater5.0

New Member
May 15, 2003
94
0
0
West Chester, Pa
Oct 23, 2007
#1
  • Oct 23, 2007
  • #1
I wanted to know if anyone knows the formula to figure out what compression ratio you will get, i.e Say i buy flat top pistons that have a 10:1 CR with a 64cc comb. chamber, and i buy heads with a 60cc comb. chamber......how can i figure out how much higher the CR will be?? ANd one more thing, im considering getting some AFR 205's for my 351W. I see that it is advertised with "mechanical" valve springs, and the 165 and 185s are advertised with Hydraulic. My question is, if i go with the 205's does that mean i have to run a Mechanical Roller cam instead of hydraulic roller b/c the heads valve springs are mechanical?? Hmmm...
 

Wallzy

New Member
Aug 20, 2006
128
0
0
Orlando, FL
Oct 23, 2007
#2
  • Oct 23, 2007
  • #2
To do it you need to know the following:

CR = Compression Ratio
Sv = Swept Volume (1/8 Engine Displacement)
Cv = Crevice Volume (all the other places that air and fuel can be: head gasket, between the piston and cyl walls above the top ring, valve relief’s)
Cc = Combustion Chamber

CR = (Cc + Cv + Sv)/(Cc + Cv)

If you know everything but your Cv, you can figure it out to be around 15.887cc. Then you can figure out what your CR is for your 60cc heads:

CR = 10.47 (if my math is correct)
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Oct 23, 2007
#3
  • Oct 23, 2007
  • #3
http://www.fordmuscle.com/calculators/compression.shtml

Bore - 4.00"
Stroke - 3.00"
Number of Cylinders - 8
Combustion Chamber Volume - 58cc
Piston Volume - (-4cc, dished piston)
Head Gasket Thickness - .039"
Deck Volume - .010"

Compression is 9.581:1


I do believe hydraulic cam springs are stronger, so take that for what it is worth.
 
I

importhater5.0

New Member
May 15, 2003
94
0
0
West Chester, Pa
Oct 23, 2007
#4
  • Oct 23, 2007
  • #4
hey thanx guys....guess ill have to do some measuring! haha! yea im not sure whats up with the valve springs either, does anyone know the difference between the hydraulic and mechanical valve springs?
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Oct 23, 2007
#5
  • Oct 23, 2007
  • #5
importhater5.0 said:
hey thanx guys....guess ill have to do some measuring! haha! yea im not sure whats up with the valve springs either, does anyone know the difference between the hydraulic and mechanical valve springs?
Click to expand...

Give me what information you have, with the above formula, and I'll do my best to fill in the rest.

Do you have a part number for the piston you are looking at?

I imagine the mechanical valve springs is for mechanical tappet cams, usually given to higher rpm capable camshafts. You will need to swap them out for some hydraulic camshaft compatible valve springs
 

samickguy15

Member
Sep 1, 2005
404
0
16
Delavan, IL
Oct 24, 2007
#6
  • Oct 24, 2007
  • #6
Call the vendor and find out if you can get the head with springs for your setup. Also, if you are by chance looking at KB's for pistons, you can punch in head size with the piston you want and it will compute the CR for you. I'm going to be running 10.2:1 with 60cc chambers and KB9925's
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 24, 2007
#7
  • Oct 24, 2007
  • #7
This is really a simple calculation.

You have basicly two volumes to consider, that with the piston at the bottom (big volume), and that with the piston at the top (small volume). Compression ratio is just the big volume divided by the small volume.

Big volume is the space above the piston in the cylinder plus the head chamber volume.

Small volume is the head volume plus the deck clearance.

There is some aggravation in rounding up all the pieces that make up the small volume, ie, chamber, valve reliefs, deck clearance, annular volume above the top ring etc, etc. Some of it you can probably neglect for practical purposes.

Its easiest to do a spreadsheet, to make it easy to look at the effect of different chamber volumes, heads, etc.
 
I

importhater5.0

New Member
May 15, 2003
94
0
0
West Chester, Pa
Oct 24, 2007
#8
  • Oct 24, 2007
  • #8
Ok, i think i have a good idea now on how to figure it out. Lemme ask one more question here concerning the heads with mechanical valve springs. My buddy at work has a 10.50s N/A 347S notchback. He has the AFR 205 heads and he has 10.9:1 CR. I asked him about the springs and he said he just converted his motor to Mechanical Roller instead of hydraulic roller, which most of us know can handle more RPM than hydraulic. My question is, since im planning on ordering the whole valvetrain soon (including the retro-fit hydraulic roller lifter kit to make my '75 351W block a roller) should i just step it up to a mechanical roller setup instead? From what i understand, the reason that you have to get retro-fit lifters to run a standard roller cam is b/c the lifter bores are to short in a flat tappet block, and the roller blocks have longer bores?? right? The guy at work said that the Mechanical roller lifters are shorter than the hydraulic roller......soooo.....could i just run a mechanical roller setup?? I think i may go out of my mind soon! Just so many dam options! Can i even do this with my block, or just stick to the hydraulic roller conversion???
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Oct 25, 2007
#9
  • Oct 25, 2007
  • #9
I personally would go with a hydraulic set-up. There may be some truth to the old tappet lifters being shorter, which I think is right, but I do not know about the lifter bore length difference.

However, the block needs to be have threads machined into the lifter valley so one can bolt-up a spider hold down bracket. It is two bolts.

The spider hold down bracket has little arms that keep these "X" shaped bars in place. The "X" shaped bars keep the roller lifters from rotating in their bores.

Hydraulic roller set-ups are usually more stable and predictable, and you can make them work with AFR 205's for sure.

I think going to mechanical route is just a way to save money. But if you are on a budget, by all means, that is okay.

Maybe someone will help you out in the conversion process
 
You must log in or register to reply here.

Similar threads

6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
497
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
SBF Head Flow Table - Work in Progress
  • Noobz347
  • Sep 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
17
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 30, 2025
Noobz347
Need some advice on upgrading GT-40-X303 heads
  • 93gtmustang
  • Sep 1, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 5, 2024
Noobz347
SOLD For Sale '92 LX Street/Drag car - WV
  • MikeyMustang
  • Apr 12, 2025
  • Fox Body Mustangs For Sale (1979-93)
Replies
4
Views
2K
Fox Body Mustangs For Sale (1979-93) Dec 31, 2025
MikeyMustang
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?