• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Help, EEC4 won't give codes!

  • Thread starter Thread starter rd
  • Start date Start date Oct 28, 2005

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 28, 2005
#1
  • Oct 28, 2005
  • #1
My 89 Notch (2.3l) ran out of gas Wed, but had a stalling problem all week.

More gas got it to run, but the check engine light is on and it runs miserably.

I jumped the single pigtail connector to the upper right EEC4 connector, but I cannot get a check engine light flash with either the KOEO or engine running tests.

I seem to have 5.8 volts to ground at both the EEC 4 connector and the single connector.

This read ok with a code reader a couple months ago.

Any suggestions?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 28, 2005
#2
  • Oct 28, 2005
  • #2
You have lost the sensor signal ground - black/white wire, pin 46 on the computer. With the power off, measure the resistance between the black/white wire on the self test connector and the negative post on the battery. You should get less than 1 ohm.



AutoZone wiring diagrams for Mustangs

http://www.autozone.com/servlet/UiB..._us/0900823d/80/16/71/3c/0900823d8016713c.jsp for 79-88 model cars

http://www.autozone.com/servlet/UiB..._us/0900823d/80/19/59/5a/0900823d8019595a.jsp for 89-93 model cars

http://www.autozone.com/servlet/UiB..._us/0900823d/80/1d/db/3c/0900823d801ddb3c.jsp for 94-98 model cars
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 29, 2005
#3
  • Oct 29, 2005
  • #3
Thanks, jrichker!

Just checked it.

I have continuity from the EEC4 connector pin to all of the plugs on circuit 46, all the way back to the 60 pin connector pin.

I did not have any continuity to ground, or to the neg bat post.

I cleaned the ground by the EEC4 box. Did not help.

I swapped in my spare EEC4, and it fired up, ran much better, the MIL was still on, and when jumped, it started flashing codes.

At least now I have some chance of figuring out whats wrong.

Thanks again!
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 29, 2005
#4
  • Oct 29, 2005
  • #4
I meant continuity to the female connector on the 60 pin connector on the harness. So the wiring is still good.

Does this mean the EEC4 box died?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 29, 2005
#5
  • Oct 29, 2005
  • #5
OOPs. the 40 & 60 are ground on a 5.0. Not sure about a 4 cylinder...
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 29, 2005
#6
  • Oct 29, 2005
  • #6
RD, FWIW, Ray III (mostly posts on the Corral) might have some input on wiring pins. He is fairly savvy with the 4 banger wiring as I recall. (There are many others, but he is the first one I thought of).

Good luck bud.
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 29, 2005
#7
  • Oct 29, 2005
  • #7
You had it right and saved my day, week, etc.

Circuit 46 on the 2.3 is the same thing, signal return. When I started, it had no continuity to the battery neg or any other ground from the EEC SIG RTN. I checked it, its the black w/white strip wire thats common to the MAP, TPS, EGR position sensor, and some other stuff, as well as the EEC4 test connector SIG RTN, upper right. ( the one you jump to get codes)

I had continuity between all of the connections in the harness, and back to the 60 pin connector in the harness. But none had a connection to the batt neg.

I swapped in another EEC4 that I got with my spare engine and trans, and I had continuity to ground from the SIG RTN, and it would flash codes on the check engine light. Finally!

I finally decided that it showed a code 22 and a code 84. 22 was no signal from the MAP, or out of range, 84 was EGR control solenoid.

I swapped in the MAP sensor from the harness that came with the spare engine, and the check engine light went out, and it ran just fine.

I finally reinstalled the other computer in the bracket, and it ran down the road fine.

Thanks, the circuit 46 info was great!!!!
 
You must log in or register to reply here.

Similar threads

2
Running very very rich
  • 2esoteric
  • Oct 31, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
469
Fox 5.0 Mustang Tech Oct 31, 2025
Noobz347
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
482
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
R
93 LX 2.3 Trouble codes 53, 85, 21 help
  • Rickshaw302
  • Apr 15, 2025
  • 2.3L (N/A & Turbo) Tech
Replies
17
Views
840
2.3L (N/A & Turbo) Tech Apr 18, 2025
AeroCoupe
Engine 1990 LX 5.0L EFI Mustang Fuel Management Problems - HELP!
  • 5.0LXStanger
  • May 25, 2025
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
45
Views
3K
Fox 5.0 Mustang Tech Jul 11, 2025
5.0LXStanger
P
CEL light on and Can't pull KOER codes.
  • psfoxstang
  • May 7, 2024
  • Fox 5.0 Mustang Tech
Replies
5
Views
1K
Fox 5.0 Mustang Tech Jun 20, 2024
psfoxstang
P
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?