• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Hood lifts

  • Thread starter Thread starter stang5093
  • Start date Start date Dec 21, 2005

stang5093

New Member
Nov 27, 2005
33
0
0
East Haven CT
Dec 21, 2005
#1
  • Dec 21, 2005
  • #1
Anyone have these? I really want to get them its just i dont know if they are wrth the money

http://www.redlinetuning.com/QL-FORD-MUS-8793.html
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Dec 21, 2005
#2
  • Dec 21, 2005
  • #2
I've used a similar product for my stock hood and it worked great. Had to get rid of them when the fiberglass hood was installed. They were just too stiff to use with the lighter, aftermarket hood.
 

stang5093

New Member
Nov 27, 2005
33
0
0
East Haven CT
Dec 21, 2005
#3
  • Dec 21, 2005
  • #3
So they are not good w/ a aftermarket hood?? I have a stock hood now but I want a aftermarket hood when I paint the car again.
 
D

DSG Man

New Member
Apr 18, 2005
17
0
0
Dec 21, 2005
#4
  • Dec 21, 2005
  • #4
I have them on my stock hood. Perhaps the aftermarket hood he spoke of would not accomodate rivets. They are simple to install. Just measure twice and drill once. MRT has a new style that doesn't require drilling. I believe it uses existing hardware to mount their brackets.
 

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Dec 21, 2005
#5
  • Dec 21, 2005
  • #5
We put some on last weekend on my buddys 90. he has an aftermarket (storman norman) hood, and right where they are supposed to attach to the hood, the fiberglass is reinforced. if you do put them on, and you go to order an aftermarket hood, look at the underside of the hood to make sure it is able to have screws ran thru it. he likes his for the added hood latch failure / hood not flying off factor. i on the other hand cannot use lifters because my glass hood doesnt have enough meat at the mounting points to put screws in it. lastly, if you put them on a glass hood, watch how you close it.. you dont want to put all the pressure on the nose of the hood. you want to have a hand on the front of the hood, and one on the side so you dont take the chance of it flexing and cracking your paint
 

stang5093

New Member
Nov 27, 2005
33
0
0
East Haven CT
Dec 21, 2005
#6
  • Dec 21, 2005
  • #6
FarBeyondDriven said:
We put some on last weekend on my buddys 90. he has an aftermarket (storman norman) hood, and right where they are supposed to attach to the hood, the fiberglass is reinforced. if you do put them on, and you go to order an aftermarket hood, look at the underside of the hood to make sure it is able to have screws ran thru it. he likes his for the added hood latch failure / hood not flying off factor. i on the other hand cannot use lifters because my glass hood doesnt have enough meat at the mounting points to put screws in it. lastly, if you put them on a glass hood, watch how you close it.. you dont want to put all the pressure on the nose of the hood. you want to have a hand on the front of the hood, and one on the side so you dont take the chance of it flexing and cracking your paint
Click to expand...


You bring up points that I did not think of like on how you close it. If I do get a hood it will be from cevinies ( spelling )
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Dec 21, 2005
#7
  • Dec 21, 2005
  • #7
I was able to attach the actuators to the hood without too much trouble. All that was required was fabricating a small bracket for each side of the hood to use as an attach point then using two part epoxy to secure it. Like I said in my original post though, the fiberglass hood was just too light to make it practical. It required a decent amount of effot to close the hood. Imagine having stiff actuators for your rear hatch then replacing the hatch with one that weighs just a third as much.
 

stang5093

New Member
Nov 27, 2005
33
0
0
East Haven CT
Dec 21, 2005
#8
  • Dec 21, 2005
  • #8
Yeah I hear you. I think I will only get them if I keep my stock hood for awhile. Thanks for your help Daggar.
 

04sleeper

Founding Member
Jun 22, 2002
2,674
14
89
Dallas, TX
Dec 21, 2005
#9
  • Dec 21, 2005
  • #9
Daggar said:
I've used a similar product for my stock hood and it worked great. Had to get rid of them when the fiberglass hood was installed. They were just too stiff to use with the lighter, aftermarket hood.
Click to expand...
Thats what I was concerned about so I just went to the parts store and made my own. These ones came from a Toyota Corolla trunk. Just made my own brackets out of some aluminum angle.
 
You must log in or register to reply here.

Similar threads

Light bulb for under hood
  • mustangfiveo198
  • May 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
463
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 8, 2026
mustangfiveo198
Engine Crankcase vent tube “relocation”?
  • Mcmahst
  • Nov 20, 2025
  • Fox 5.0 Mustang Tech
Replies
17
Views
878
Fox 5.0 Mustang Tech Dec 20, 2025
manicmechanic007
3.08 gears with a manual trans
  • limp
  • Aug 27, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3
Replies
43
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 14, 2026
Qtrhrse23
5
New to this
  • 5.ohCS
  • Nov 1, 2026
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
0
Views
107
2005 - 2014 S-197 Mustang -General/Talk- Nov 1, 2026
5.ohCS
5
S
Drivetrain Downshifting from 3rd to 2nd issue
  • Scott_S
  • Apr 23, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
35
Views
1K
Fox 5.0 Mustang Tech Oct 12, 2026
limp
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?