How much rwhp?

1qckFOX

New Member

Jan 1, 2004

139

0

0

Jan 1, 2004

#1

• Jan 1, 2004

• #1

Hey guys. I'm a NooB here but ive been browsing these board for a while. What do you think my RWHP and Torque is with these mods? On and Off the bottle. Thanks


24# 73mm C&L MASS AIR
75 or 70 TB BBK
Cobra upper and lower intake
E303 cam
MAC shortie headers
Mac H-pipe
Mac mufflers
Elderbrock 75 shot
Ford perfomance underdrive pullies
Mac cold Air kit
Optima Red top

 

mike keirstead

New Member

Aug 6, 2003

1,121

0

0

ROLLING A JOINT

Jan 1, 2004

#2

• Jan 1, 2004

• #2

First of all 75mm TB is way to big. 65 or 70 is good.

Without spray---220 rwhp TOPS
With Spray---260 rwhp TOPS

Assuming your motor is healthy and in good tune.

Your heads are choking your motor from making good power...also you didnt mention a good fuel pump.

Pretty much have to have one with the spray.

 

Fox Saleen 163

New Member

Dec 5, 2003

286

0

0

San Diego, CA

Jan 1, 2004

#3

• Jan 1, 2004

• #3

Just some friendly advice, I wouldn't run the 75mm TB. Might be a good idea to even go down to a 65mm. Basic rule of thumb is not to use a TB bigger than your MAF meter.

Not sure about how much power you will put out, I don't want to guess and get a bunch of crap for it.

 

mike keirstead

New Member

Aug 6, 2003

1,121

0

0

ROLLING A JOINT

Jan 1, 2004

#4

• Jan 1, 2004

• #4

Maybe 230 rwhp and 280 ft/lbs no spray
275 rwhp and 325 ft/lbs with.

Again assuming that is a 5 speed also.

 

1qckFOX

New Member

Jan 1, 2004

139

0

0

Jan 1, 2004

#5

• Jan 1, 2004

• #5

Yeah It's a 5 spd. with 30k miles. Thanks guys

 

1qckFOX

New Member

Jan 1, 2004

139

0

0

Jan 1, 2004

#6

• Jan 1, 2004

• #6

What do you all think i will make with some GT-40 irons?

 

mike keirstead

New Member

Aug 6, 2003

1,121

0

0

ROLLING A JOINT

Jan 1, 2004

#7

• Jan 1, 2004

• #7

250-255 no spray.

 

1qckFOX

New Member

Jan 1, 2004

139

0

0

Jan 1, 2004

#8

• Jan 1, 2004

• #8

mike keirstead said:

250-255 no spray.

Click to expand...

Damn didn't think i would pick up that much for only $300.


Next mod: gt40 iron heads

 

mike keirstead

New Member

Aug 6, 2003

1,121

0

0

ROLLING A JOINT

Jan 1, 2004

#9

• Jan 1, 2004

• #9

They are worth 20-25 rwhp....i just got a set for 190.

 

mike keirstead

New Member

Aug 6, 2003

1,121

0

0

ROLLING A JOINT

Jan 1, 2004

#10

• Jan 1, 2004

• #10

Remeber.....this is all a guess. You may gain More/less. I am just going of what ive seen before.

 

X

xplo89gt

Founding Member

Jul 14, 1999

945

0

16

Boston, MA

Jan 1, 2004

#11

• Jan 1, 2004

• #11

I would guess 230rwhp maybe more if you have a good tune.

I pulled off 227rwhp with exhaust, pullies, maf, timing...

 

1qckFOX

New Member

Jan 1, 2004

139

0

0

Jan 2, 2004

#12

• Jan 2, 2004

• #12

Damn $190 the cheapest I can find them is for $300

 

RyanSG

Founding Member

Oct 24, 2002

286

0

17

Allentown, Pa

Jan 2, 2004

#13

• Jan 2, 2004

• #13

i've seen a stang with a bad engine blew out black smoke one cylender was almost dead. And that made 220Hp at the RW. all it had was a high flow exhaust. so that shoudl give a judge as to how good these engines really are

 

mike keirstead

New Member

Aug 6, 2003

1,121

0

0

ROLLING A JOINT

Jan 2, 2004

#14

• Jan 2, 2004

• #14

1qckFOX said:

Damn $190 the cheapest I can find them is for $300

Click to expand...

Ebay...i got lucky