• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 V6 Mustang Tech

Humming Noise In My 2002 3.8l V6

  • Thread starter Thread starter cgdz
  • Start date Start date Jul 24, 2012
C

cgdz

New Member
Jul 24, 2012
1
0
1
Jul 24, 2012
#1
  • Jul 24, 2012
  • #1
Hello everyone. I recently started noticing this humming noise while on the highway. It seems to come from the front left side and I can feel a very light, but fast vibration on the pedals especially when pressing down on the brake pedal. It seems to only happen at 40+ mph. Turning at those speeds is also strange; when I switch lanes the car doesn't turn completely smoothly. It seems to jerk a little bit. It also feels a bit like the car is leaning a bit to the left.

I'm thinking this might be the wheel bearing, but I'm not sure. This started soon after taking it to a mechanic. He replaced the front brake rotors and brake pads and says he "rebuilt" the front left wheel bearing because he said he noticed some play in the tire when it was on the lift. Could it be that it wasn't properly repaired?

This is happening on a 2002 3.8L V6 Ford Mustang.

Thanks for taking the time to read this and reply.
 

kramer

Member
May 8, 2012
75
1
8
stonewall oklahoma
Aug 4, 2012
#2
  • Aug 4, 2012
  • #2
first off make sure that its perfectly aligned , that means when the steering wheel is straight ahead it drives straight and not even slightly left or right , im not familiar with 2002 3.8s , but it may be a tie rod end going bad , and if they have grease inserts then grease them, but not to much , just 1 and a half squirts , the hum may actually be coming from the differential , and may mean it needs new lubricant , but is actually really unlikely if its coming from the front left especially at 40plus , i kinda doubt these problems are connected but definantly could be , also check your serpantine belt, should be super tight
 

g96v6-250k

Member
Aug 15, 2012
91
1
8
Aug 17, 2012
#3
  • Aug 17, 2012
  • #3
sounds like bad bearing or bad camber check for abnormal wear on the inside edge of that tire.
i was cruising on the highway at 75 and out of nowhere a bearing started doing this. these bearing hubs need a new nut if they are removed, maybe he didnt do that. try to retorque it first i think it needs 300 ft lbs. or try a new nut. good luck finding that torque wrench.
 
You must log in or register to reply here.

Similar threads

T
2002 V6 3.8L Help Me
  • TheIncompetentMechanic
  • Apr 4, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2 3
Replies
50
Views
869
1996 - 2004 SN95 Mustang -General/Talk- May 12, 2026
TheIncompetentMechanic
T
H
Strange steering/brake issue
  • Haxmaster
  • Jun 2, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
93
SN95 4.6L Mustang Tech Jun 3, 2026
squeak93
J
2004 Mustang 3.8L V6 vibrations above 65 MPH and differential leaks
  • joeybuddy96
  • Mar 16, 2026
  • SN95 V6 Mustang Tech
Replies
16
Views
597
SN95 V6 Mustang Tech Jul 14, 2026
joeybuddy96
J
D
Resolved 1985 GT brake pedal problems
  • DienstXIV
  • Jun 19, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
500
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 2, 2025
DienstXIV
D
J
Severe shaking/vibrations in steering wheel
  • jacket999
  • May 20, 2025
  • SN95 V6 Mustang Tech
Replies
8
Views
844
SN95 V6 Mustang Tech Jun 1, 2025
NtheGAME
N
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 V6 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?