JR, RC, anyone else... Gauge cluster question

1105 · Jul 17, 2004

How do you seperate the clear plastic from the black part that divides all of the gauges up? It looks like its glued on. Heres a pic of what I'm talking about... Silver part surrounding the gauges.

AznStanger3v · Jul 17, 2004

you remove the two allen screws. then there are like 4 philips head screws. unhook some stuff and pull it out. then seperate the plastic by the clips i think. its been a while. i was just experimenting around a looooong time ago. i could be wrong

1105 · Jul 17, 2004

I can get the black piece and the clear piece out as a whole.. but cant get them seperated... I didnt see any screws holding it on but I might have over looked them?

94GTLaserRC · Jul 17, 2004

Zach, Im flattered that you asked me...BUT, I havent done this yet....but Im subscribing...JR...HELP!!!

RC

1105 · Jul 17, 2004

well I know you can help me with this RC... How do you get the clock out? Isnt it just a swift hit towards the windshield and its loose? Also... how do the door pods come out? Dont you need to take the things around the handles off and theres a screw back there or something? I havent done it in a year and I cant seem to get thoes handle things off to see if there is a screw behind it.

94GTLaserRC · Jul 17, 2004

The clock lifts out..So does the door bezel. There are those plastic thingies with the metal that holds them into the holes. The door bezel should lift enough to access the wires by digging your fingers in the rear most part where the curve is and lifting...Problem is those plastic clips are old and they break easily..Mine broke off, and I have some double stick tape hold it down in that one spot.
RC

1105 · Jul 17, 2004

Got the clock pod painted... I tried lifting the door pods out but they wouldnt budge. I could have swore there was a screw holding them on... Almost done with painting stuff though. Got my door pods left and teh gauge cluster if I can figure out how to seperate the two

donjohn · Jul 18, 2004

in the faq section where they talk about replacing the door gear it shows how to get the door bezels out too.

AznStanger3v · Jul 18, 2004

door bezels just use plastic clips. use a flat head and CAREFULLY pry around. itll pop right out

1105 · Jul 18, 2004

Thanks...

anyone know how to get to the part of the gauge cluster I was talking about?

94TURBO5 O · Jul 18, 2004

Zach

Take off those brass looking screws around it and it should pop off.

1105 · Jul 18, 2004

I took those screws out but that just seperates the black and clear piece from the rest of the gauge cluster... I think the clear piece is glued on or something. I tried to pry it off but it started to crack so I stopped

Black Stampede · Jul 18, 2004

Hey guys. I want to paint my door cup plastic pieces black (same color they already are but they are getting worn). What grits do I need to sand them with first and what paint do I use?
Thanks alot!

94GTLaserRC · Jul 18, 2004

Black Stampede said:
Hey guys. I want to paint my door cup plastic pieces black (same color they already are but they are getting worn). What grits do I need to sand them with first and what paint do I use?
Thanks alot!

Just use a REALLY light scuffing with a 400 grit...do not apply any real pressure. Since you are going black, and those door handles are plastic, I would go with Krylon Black Fusion.

JR...When you mention painting the "cups" are you referring to the little piece that surrounds the handle, or the larger piece that you grab when you close the door, that houses the window switches?
Thanks
RC

tangerinesaleen · Jul 18, 2004

As far as seperating the clear plastic from the black section that outlines the gauges. Yes, It's glued, or melted together, whichever. I used an exacto knife and a dremel tool to seperate them. After you paint the black part, you can just glue them back together. Just be very careful when you do this. if you use too much glue, it will cause the clear lens to cloud up around where you have glued it. Use as little glue as possible.

94GTLaserRC · Jul 18, 2004

tangerinesaleen said:
As far as seperating the clear plastic from the black section that outlines the gauges. Yes, It's glued, or melted together, whichever. I used an exacto knife and a dremel tool to seperate them. After you paint the black part, you can just glue them back together. Just be very careful when you do this. if you use too much glue, it will cause the clear lens to cloud up around where you have glued it. Use as little glue as possible.

Hey...Tang Saleen...I see youre from Pompano...Do I know you? IM surprised you are just now getting on here?

We're planning a Towers night in 2 weeks
RC

Black Stampede · Jul 18, 2004

RC, where can I buy this Krylon black fusion paint?
Thanks

94GTLaserRC · Jul 18, 2004

Black Stampede said:
RC, where can I buy this Krylon black fusion paint?
Thanks

Walmart...And buy A LOT!!!
I need my 150+ shares of stock to reach $60 by the end of the year so I can get my pool!
IM sure Home Depot has it
RC

94TURBO5 O · Jul 18, 2004

94GTLaserRC said:
JR...When you mention painting the "cups" are you referring to the little piece that surrounds the handle, or the larger piece that you grab when you close the door, that houses the window switches?
Thanks
RC

Yep the whole thing

1105 · Jul 18, 2004

thanks tangerine! I figured it was glued on but wanted to make sure before i go cutting it off.

I need my 150+ shares of stock to reach $60 by the end of the year so I can get my new rims and give my tribars to zach when he comes down for towers!

there ya go RC, fixed it for ya

I got my door cups off, started sanding them then went out with a friend. I'll finish them tomorrow along with the gauge thing and post pictures of the final product To remove the door pods, pry out the very top first, then theres one pressure clip in the back... One of mine was broken off and the other one broke when I took the pod out... I dont think it'll matter

JR, RC, anyone else... Gauge cluster question

1105

I AM the random post master...bow down

AznStanger3v

Active Member

1105

I AM the random post master...bow down

94GTLaserRC

Squint as you approach, lest you be blinded by my

1105

I AM the random post master...bow down

94GTLaserRC

Squint as you approach, lest you be blinded by my

1105

I AM the random post master...bow down

donjohn

New Member

AznStanger3v

Active Member

1105

I AM the random post master...bow down

94TURBO5 O

New Member

1105

I AM the random post master...bow down

Black Stampede

94GTLaserRC

Squint as you approach, lest you be blinded by my

tangerinesaleen

New Member

94GTLaserRC

Squint as you approach, lest you be blinded by my

Black Stampede

94GTLaserRC

Squint as you approach, lest you be blinded by my

94TURBO5 O

New Member

1105

I AM the random post master...bow down

Similar threads

JR, RC, anyone else... Gauge cluster question

I AM the random post master...bow down

Active Member

I AM the random post master...bow down

Squint as you approach, lest you be blinded by my

I AM the random post master...bow down

Squint as you approach, lest you be blinded by my

I AM the random post master...bow down

New Member

Active Member

I AM the random post master...bow down

New Member

I AM the random post master...bow down

Squint as you approach, lest you be blinded by my

New Member

Squint as you approach, lest you be blinded by my

Squint as you approach, lest you be blinded by my

New Member

I AM the random post master...bow down

Similar threads

Privacy & Transparency

Privacy & Transparency