Fox Lets make my AC work again

93CalypsoConvert · Apr 27, 2021

After taking the convertible out on a hot day, I found that AC would've been EXTREMELY nice to have. So I want to make my AC work, but I don't know where to start. This car started as a 1993 4 banger convertible, but has since been swapped to a carbureted 5.0. This swap was done by the previous owner and most of the electrical systems were removed/disabled. From the looks of it, the car has most of the parts required for AC. Right now, I think only the the soft lines and clutch wiring is missing.

Here are some pictures of what I've got:

This is the compressor. It looks to be in great condition, but it has been disconnected for quite some time. Turns free and creates pressure/suction out of the holes. The clutch wiring is not connected, nor do I know where it is. I am unsure where this harness would be or where is would come from.

Here are the lines going into the vehicle. Everything here looks to be in great condition and undamaged. The pressure switch is installed doesn't seem to be messed with during the swap.

Here are the lines in it right now. I think this is where it would've connected to the compressor on the four cylinder, but I am not sure.

There is a plethora of disconnected harnesses near these lines. I have a feeling one of these is likely the compressor clutch harness, but again, I am not sure.

So could it be as simple as connecting the the clutch and installing the correct lines/hoses, then charging the system? If not what all needs addressed?
I don't necessarily want to spend a lot of money on this and I still have to decide if I want to screw with converting r12 to r134a.

Thanks.

jsgif99 · Apr 28, 2021

I bought the LMR conversion kit so I can run the new freon. I can't answer any specific questions because I had a Ford expert mechanic install it. That was over a year ago. Love the system. It still works awesome.

Potomus Pete · Apr 28, 2021

jsgif99 said:
I bought the LMR conversion kit so I can run the new freon. I can't answer any specific questions because I had a Ford expert mechanic install it. That was over a year ago. Love the system. It still works awesome.

Do you know what kind of freon?? 134 or R12a

HemiRick · Apr 28, 2021

If its a 1993 car it should be set up for 134a......

93CalypsoConvert · Apr 29, 2021

Potomus Pete said:
Do you know what kind of freon?? 134 or R12a

R12

93CalypsoConvert · Apr 29, 2021

HemiRick said:
If its a 1993 car it should be set up for 134a......

1993 still used R12

Mustang5L5 · Apr 29, 2021

How long has the system been opened?

your most important task really is flushing the system and ensuring no debris is inside. It will block the orifice tube (which should be replaced anyway) and cause issues.

R134a is not compatible with mineral oil, so a total system flush is necessary regardless.

i recommend new o rings. You’ll want to assemble the system with the recommended oil in rhe

once the system is assembled you need to pull a DEEP vacuum. 500 microns or better.

After that, charge with desired Freon. I prefer R12. It’s pricey, but available on eBay. A license is required technically but I have yet to ever have anyone ask to see mine.

I’m doing my ac system over as part of my rebuild with all new parts and R12

Potomus Pete · Apr 30, 2021

Mustang5L5 said:
How long has the system been opened?

your most important task really is flushing the system and ensuring no debris is inside. It will block the orifice tube (which should be replaced anyway) and cause issues.

R134a is not compatible with mineral oil, so a total system flush is necessary regardless.

i recommend new o rings. You’ll want to assemble the system with the recommended oil in rhe

once the system is assembled you need to pull a DEEP vacuum. 500 microns or better.

After that, charge with desired Freon. I prefer R12. It’s pricey, but available on eBay. A license is required technically but I have yet to ever have anyone ask to see mine.

I’m doing my ac system over as part of my rebuild with all new parts and R12

Your right Mike. I went through the whole process, but didn't clean enough. My orafice is clogged and freezes up at the tube. Redoing the whole thing soon with more new parts. Did the whole thing, and getting hot air. I am ordering Freeze 12. It doesn't need heavy vacuum, and moisture resistant. Can't wait because we are about to get into the nineties every day......Taking the whole thing apart and cleaning,new dryer. the only thing left is the thing by the heater box

TOOLOW91 · May 1, 2021

Potomus Pete said:
Your right Mike. I went through the whole process, but didn't clean enough. My orafice is clogged and freezes up at the tube. Redoing the whole thing soon with more new parts. Did the whole thing, and getting hot air. I am ordering Freeze 12. It doesn't need heavy vacuum, and moisture resistant. Can't wait because we are about to get into the nineties every day......Taking the whole thing apart and cleaning,new dryer. the only thing left is the thing by the heater box

Pete ,The deeper the vacuum you get any system into the better the system performs . You want as little moisture and trash as possible .

Potomus Pete · May 1, 2021

Ordering up some Freeze 12 this weekend, and getting this going. It's getting very hot in Florida. My car is fast=so happy.

Zeffer · May 1, 2021

I totally redid my A/C when I bought my 89....The picture of your compressor is an older R12 style (like mine) the picture you show of your lines have the newer R134a connections, which wont attach to your compressor. You need to buy the suction and discharge line which will attach to your compressor. This is important for two reasons, one it will come with a new receiver/dryer, and two you will have the other line that has the orfice tube installed. If the system has been open to atmosphere for a long time the drier will be saturated with moisture from the ambient air. I would replace all orings and make sure you use the correct oil with whichever refrigerant you decide on.

Fox Lets make my AC work again

93CalypsoConvert

Active Member

jsgif99

Member

Potomus Pete

I'm still waiting for the fully nude shots

HemiRick

I'd be looking at jacking under the house

93CalypsoConvert

Active Member

93CalypsoConvert

Active Member

Mustang5L5

That is…until I whipped out my Bissell

Potomus Pete

I'm still waiting for the fully nude shots

TOOLOW91

If you're the village idiot what's that make me?

Potomus Pete

I'm still waiting for the fully nude shots

Zeffer

Member

Similar threads

Fox Lets make my AC work again

Active Member

Member

I'm still waiting for the fully nude shots

I'd be looking at jacking under the house

Active Member

Active Member

That is…until I whipped out my Bissell

I'm still waiting for the fully nude shots

If you're the village idiot what's that make me?

I'm still waiting for the fully nude shots

Member

Similar threads

Privacy & Transparency

Privacy & Transparency