My new engine

Pro-Hawk · Jul 20, 2007

sleeper_inc said:
Yup, 15 and live in a very small town, the only job I can have right now is working in a store, but they wont call me back after 5 resumes

OIC.

Well if I was 15 years old I wouldn't even think about working lol. Once you start it never stops Just worry about getting an education and cars want be a problem.

sleeper_inc · Jul 21, 2007

This is as far as the engine is now, just have to remove the turbo from the manifold, drill holes at the end of the crack and cut a V grove in it, get it welded put it on and its ready for the swap

hyperse7en · Jul 21, 2007

this brings me back to when i did my merkur swap. mine wasnt that dirty though LOL be prepared to fork out to rebuild it. i spent about a grand rebuilding mine. i picked up a complete merkur (not running, needed a little time, and smarts)
its lookin good! keep us updated on it!
jeff

PS i have an E6 manifoldyou just pay $30 plus shipping (i assume about 15 bucks) and its yours.

sleeper_inc · Jul 21, 2007

****!!!!!!!!!!!!!!!!! I guess that crack in my manifold is bigger than I though. Its ****ing HUGE!!!! I had to redrill a hole (as you can see) because it just kept going...

Pro-Hawk · Jul 22, 2007

Now are you sure thats an E6 manifold?

sleeper_inc · Jul 22, 2007

Its an E3, I went on stingers site and he called his an E6 and it looked the exact same as mine so... my bad lol

Pro-Hawk · Jul 22, 2007

sleeper_inc said:
Its an E3, I went on stingers site and he called his an E6 and it looked the exact same as mine so... my bad lol

Ya, the E6 has a little more meet around the area where your manifold is cracked. Just get ready for it to crack again...probaly sooner than later. I would take up hyperse7en on his E6 before I tried using a welded up E3.

Best of luck,
Ray

sleeper_inc · Jul 22, 2007

I would take him up but I'll be upgrading to a bedder one this upcoming summer so I'll just wait for now, plus the engine will be stock for now as well because snow + power = ditch

hyperse7en · Jul 23, 2007

eeeh.......have you looked at the price of an aftermarket head lately?? i would spend the money on a rebuild before i spent it on a header. thats just me though.

Pro-Hawk · Jul 23, 2007

sleeper_inc said:
I would take him up but I'll be upgrading to a bedder one this upcoming summer so I'll just wait for now, plus the engine will be stock for now as well because snow + power = ditch

Well atleast you'll have plenty of experience in pulling manifolds come next Summer. So what is your goal for this car anyways? You must be planning something pretty serious if you need something better than a stock manifold?

sleeper_inc · Jul 23, 2007

I want a 450-500 HP car, pushing 25PSI on a daily basis and run 30-35 PSI on the track, with no pinging and all on pump gas.

I hope this aint to much to ask lol

Pro-Hawk · Jul 23, 2007

sleeper_inc said:
I want a 450-500 HP car, pushing 25PSI on a daily basis and run 30-35 PSI on the track, with no pinging and all on pump gas.

I hope this aint to much to ask lol

That isn't a unreallistic goal and a Ported E6 should do just fine. I would apply that money for a header towards a T3/T4 hybird. This will bolt right up to a stock manifold and is good for 450hp. You'll need a FMIC as well. The stock ones don't handle much more than 20psi I think but the hoses clamps usualy blow off around 18psi. It's been a while but that should be pretty close. The rest is typical stuff like built motor and a nice head.

sleeper_inc · Jul 23, 2007

Anyone got an E6? no one around me will touch my manifold for less that $40, so what the hell.

Shipping I have no clue, but my postal code is s0g-4c0 (p.o. box 216)

hyperse7en · Jul 24, 2007

*raises hand* i have one. read pervious posts.

Red_LX · Jul 25, 2007

You wanna drive that thing in the snow?

Might consider just disconnecting the wastegate actuator over the winter....seriously.

I have enough problems with wheelspin on wet roads in my car, I don't even try to drive it during the months of november through march.

sleeper_inc · Jul 25, 2007

I have no option but to drive it in snow, its my only car right now.

How much did you want for the manifold hyperse7en? If you could also figure out how much shipping is than that would be great.

Regina Beach Saskatchewan P.O. Box 216 s0g4c0

Red_LX · Jul 25, 2007

So like I said, disconnect the wastegate actuator...it'll make the car a hell of a lot more driveable in winter.

sleeper_inc · Jul 25, 2007

I'll just turn the boost down to 5-10 PSI

Pro-Hawk · Jul 25, 2007

Well I would listen to people if you want to see that 18th birthday. Just having zero boost and a limited slip is enough fun in the snow.

sleeper_inc · Jul 25, 2007

I guess thats true, but I wanna make it up this major hill I have to go up to get home from school, and I wanna be doing at least the speed limit lol

My new engine

New Member

New Member

Member

New Member

New Member

New Member

New Member

New Member

Member

New Member

New Member

New Member

New Member

Member

I’m not much help unless you’re looking for ****!

New Member

I’m not much help unless you’re looking for ****!

New Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency