• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

New Guy With A Fox And Newbie Questions.

  • Thread starter Thread starter Nitsua93
  • Start date Start date May 5, 2013
N

Nitsua93

New Member
May 5, 2013
4
0
1
May 5, 2013
#1
  • May 5, 2013
  • #1
Picked up an '88 GT to replace my current daily. It's pretty rust free. No rust to worry about on the strut towers or above the wheels. Has 88K on it. I'm going to rebuild the T5 soon and clean a lot of things up before I begin nodding.

Now for the questions! I have a slight wander in the front suspension from time to time which makes things a little sketchy when doing a pull. Is there anything common to go bad up there?

How do I know if my clutch cable needs tightened?

I've found an on/off switch under the steering column. Is there a reason anyone could think of why it's there?
 

CarMichael Angelo

my rearend will smell so minty fresh,
15 Year Member
Nov 29, 1999
10,641
8,909
234
Birmingham, al
May 5, 2013
#2
  • May 5, 2013
  • #2
1. You have 88k on a car that's 25 years old. Front suspension/steering parts (i.e. inner/outer tie rod ends) are probably worn out. Take it for a front end alignment,...they'll advise you as to what is worn out on a car that "wanders" in the lane,...then you can replace what they diagnose as bad, and take it back to the shop for a real alignment.

2. You know if your clutch needs adjustment by where it starts to engage when you start to let the pedal out. If you have the stock N/A clutch cable still installed, you can give the clutch pedal an upward pull w/ your hand,...there is an auto adjuster that will do it for you.

3. It's probably a kill switch. Your previous owner put it there to allow an extra measure of security to keep the car from being jacked when parked in " suspicious surroundings"

Tell me more about this "nodding" you speak of,...is that some sort of practice where you eat a late lunch, and then get on the interstate w/ the heat turned up a little too high?
 
9

95PGTTech

Member
Jan 28, 2008
302
20
19
May 5, 2013
#3
  • May 5, 2013
  • #3
Up front - everything. It's a 25 year old car. Get the front up in the air, check the wear pattern on the front tires and shake the front end down. A couple quick failure points that would cause a wander - play in the tie rods, steering shaft, lower ball joints, shocks, lower control arm bushings. If you don't know how to step-by-step shake the front end down to isolate specific faults rather than just guess and check throw parts at it, ask. Lots of really great help on these forums.

The OEM clutch cable can't really be "tightened" as it is not adjustable. If there is play in it (slop at the top of the travel before actuation), it needs to be replaced. There is a ratcheting mechanism on the OEM clutch pedal meant to tighten up that slack as the cable lengthens from age but they are horrible and rarely work, often breaking (the quadrant). This and the firewall adjuster should be replaced with aftermarket pieces (see: Fore). The clutch cable should be replaced with ONLY an OEM cable - aftermarket adjustable ones have the reliability of a Pontiac Fiero.

Is it clearly aftermarket? Usually this is indication of an aftermarket-installed security system. Trace the wires and decide if you want to keep it or go back to the OEM stuff.
 
N

Nitsua93

New Member
May 5, 2013
4
0
1
May 5, 2013
#4
  • May 5, 2013
  • #4
Thanks! The wires are extremely hard to trace because the seat will not slid backwards. It's a very tight squeeze to get under the dash. In the back seat I found a remote and under the steering column I found an impact alarm.
 
N

Nitsua93

New Member
May 5, 2013
4
0
1
May 5, 2013
#5
  • May 5, 2013
  • #5
madmike1157 said:
3. It's probably a kill switch. Your previous owner put it there to allow an extra measure of security to keep the car from being jacked when parked in " suspicious surroundings"

Tell me more about this "nodding" you speak of,...is that some sort of practice where you eat a late lunch, and then get on the interstate w/ the heat turned up a little too high?
Click to expand...
Haha I meant modding it's definitely not a kill switch. It's wired for an amp so I imagine may have had something to do with that.
 
You must log in or register to reply here.

Similar threads

Suspension 87 steering wheel slightly wobbles after new Rag joint install
  • R82148V
  • Jun 16, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
25
Views
978
Fox 5.0 Mustang Tech Jun 24, 2025
R82148V
S
Fox New to me 82 GT
  • Stangman7082
  • Jan 20, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3
Replies
41
Views
3K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 18, 2025
AeroCoupe
H
New kid on the block
  • HydraX
  • Mar 22, 2025
  • The Welcome Wagon
Replies
17
Views
762
The Welcome Wagon Mar 22, 2025
HydraX
H
E
Finished my Fox Hydroboost Install - Tips
  • Engineer Duane
  • Apr 9, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 5, 2025
Engineer Duane
E
Wheels-Tires LS mii swap and rear rim size/axle questions....
  • 78mIIman
  • Feb 2, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
6
Views
735
1974 - 1978 Mustang II Talk & Tech May 6, 2025
78 Mach1
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?