• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

oh crap.....

  • Thread starter Thread starter 88mustang92
  • Start date Start date Mar 3, 2008
8

88mustang92

Member
Mar 1, 2008
105
0
16
Mar 3, 2008
#1
  • Mar 3, 2008
  • #1
um...****??? idk this is very screwy, freshly built 1988 mustang 5.0 HO motor...had it done in december and have started it monthly..Started it yesterday n waited for her to get warm then reved it to about 3 grand then clunk clunk clunk...(shuts key off) I looked in my engine compartment and the top of my Timing Chain Cover is pretty much in pieces, n its only the top i have no clue wtf happened... I can see the chain if i go outside right now, i have already picked up the chunks that landed on the ground and under the car.. I have a new timing chain cover on its way so any thoughts?
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Mar 3, 2008
#2
  • Mar 3, 2008
  • #2
It sounds like the timing chain broke or if not, the cam had too much endplay and the gear made contact with the cover and chewed a nice hole in it.
 

dcurtis

10 Year Member
Jan 19, 2006
688
7
39
Mar 3, 2008
#3
  • Mar 3, 2008
  • #3
I vote on stapped chain
 
8

88mustang92

Member
Mar 1, 2008
105
0
16
Mar 3, 2008
#4
  • Mar 3, 2008
  • #4
well i do not think the timing chain snapped (double roller) b/c as i look down inside it seems like the chain looks fine and the cam is a B303 not even 3000 miles on it...when it was replaced all cam bearing were replaced and so was timing chain and gear...idk guys can't wait 2 tear into it..... so how bad i screwd up on my first motor.
 

Flavadave4

Active Member
Nov 28, 2003
1,044
21
49
Utica, NY
Mar 3, 2008
#5
  • Mar 3, 2008
  • #5
Sucks to hear, any pics?
 

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Mar 3, 2008
#6
  • Mar 3, 2008
  • #6
I guarantee that little retainer plate that holds the cam in was not tightened down/loctited and came loose. As Matt stated, the cam probably just walked out, hit the timing cover, and did what it did.
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Mar 3, 2008
#7
  • Mar 3, 2008
  • #7
would that toast a motor?
 
G

greg251

New Member
Dec 17, 2006
55
0
0
Mar 3, 2008
#8
  • Mar 3, 2008
  • #8
Did you use the right bolts on the lifter dog bone hold down? If they are too long they will seize the cam up and bust the chain.
 

Gearbanger 101

Straight Outta Locash
20+ Year Stangneter
Aug 10, 2002
9,457
1,377
234
Ontario, Canada
Mar 3, 2008
#9
  • Mar 3, 2008
  • #9
Missing any tools since you put it together? A small wrench, or socket perhaps?
 
8

88mustang92

Member
Mar 1, 2008
105
0
16
Mar 3, 2008
#10
  • Mar 3, 2008
  • #10
no missing sockets or anything, but i think maybe NKau maybe onto something...i did not lock-tite the came retainer bolts...i do have a pic on my phone which will be here shortly.
 
8

88mustang92

Member
Mar 1, 2008
105
0
16
Mar 3, 2008
#11
  • Mar 3, 2008
  • #11
here is the pic
 

Attachments

  • pci2.webp
    19.7 KB · Views: 187

93 LX

Founding Member
Jun 2, 2000
3,081
3
0
Norwalk, CA.
Mar 3, 2008
#12
  • Mar 3, 2008
  • #12
nice.. it looks like the cam walked..
 

Fast63

New Member
Sep 20, 2007
717
0
0
Mar 3, 2008
#13
  • Mar 3, 2008
  • #13
the thrust plate holding the cam in could have broken.
 
8

88mustang92

Member
Mar 1, 2008
105
0
16
Mar 3, 2008
#14
  • Mar 3, 2008
  • #14
idk when it gets warm again im gonna take the front of it apart n wat not...check out wtf is going on..in case the cam did walk, would there b alot of damage?
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Mar 3, 2008
#15
  • Mar 3, 2008
  • #15
88mustang92 said:
in case the cam did walk, would there b alot of damage?
Click to expand...

only one way to find out eh eh?

This happened to someone else on here using a Trickflow timing set, something about them made it do that, I forget what happened. Sounds like something was left loose.
 

LiquidGT

Member
Oct 8, 2007
368
0
16
Near STL hell
Mar 4, 2008
#16
  • Mar 4, 2008
  • #16
Black1987Stang said:
This happened to someone else on here using a Trickflow timing set, something about them made it do that, I forget what happened. Sounds like something was left loose.
Click to expand...

My TFS chain instructions said to countersink the bolt holes in the thrust plate (therefore making it weaker) and use the little phillips screws they supplied. wtf?

Luckily I saw that thread so I didn’t follow their directions so my engine is still running strong after four months.
 
8

88mustang92

Member
Mar 1, 2008
105
0
16
Mar 4, 2008
#17
  • Mar 4, 2008
  • #17
hey i was told by my dad there is a cetain slack in the chain that a manual tran car needs...is this true or how can u even adjust that...and also the bolt and the spacer that looks like a small L bracket cept its not as rigid (cam retaining bolt and other thing that goes with it to hold the gear into place) i placed the rounded end into the ovals in the gear...was that right? if not o **** and if so well cool.well any thoughts on the slack theory?
 

cenok is family

15 Year Member
Jun 25, 2003
1,409
69
79
Norman, Ok
Mar 4, 2008
#18
  • Mar 4, 2008
  • #18
ouch...are you sure the chain didn't break and is just laying over the sprockets? sure looks like chain break carnage to me. and yes there is a certain amount of slack that should be in the chain, but thats not specific towards manual tranny cars, and it's really not THAT much slack, espcially in a brand new chain. maybe an 1/8" flex each way?
 
8

88mustang92

Member
Mar 1, 2008
105
0
16
Mar 4, 2008
#19
  • Mar 4, 2008
  • #19
got the cover 2day along with some felpro gasket 2day n took a chunk out of the old one 2day even though its still on the motor....i tried to life the chain off but it didn't seem 2 budge...i hope it gets nice soon i really want this car 2 run i have 2 many cocky supra friends with stock motors they keep braggin 2 me cuz my other stang is a 92 LX with a 2.3L.....sure good fuel economy but noooo power wen it you see it go past your house and i get on it it sound like this............(iiiiiiiiiiiiMMMMMMMM GAaaayyyyyyy) im like stfu ill put a 347 in you and change ur damn mind on saying **** like that lol well enough fantasizing time to get this motor running
 

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Mar 5, 2008
#20
  • Mar 5, 2008
  • #20
Take the cover off, and find out what happened. Get back to us, and we may be able to shed some light on any other problems that might have occurred as a result.
 
You must log in or register to reply here.

Similar threads

M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
843
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
S
Requesting Guidance for 306 motor swap - Fuel? - SD? MAF?
  • So_Flo
  • Jul 26, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
32
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 4, 2026
Mcmahst
Resolved Coolant blowing out of valve cover??
  • sav22rem22
  • Nov 1, 2023
  • Fox 5.0 Mustang Tech
Replies
19
Views
5K
Fox 5.0 Mustang Tech Nov 19, 2023
sav22rem22
S
what would you do? sell the project and buy completed or finish project?
  • STANG32
  • Feb 8, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
4
Views
721
1965 - 1973 Classic Mustangs -General/Talk- Feb 16, 2025
rusty428cj
Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
46
Views
4K
1965 - 1973 Classic Mustangs -General/Talk- Jul 16, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?