p.i. swap difference?

96 GT JOE · Apr 26, 2006

I have a couple of questions about doing a p.i. swap on a 96 GT:

- am i better off buying the parkway performance complete p.i. swap kit ($1350), or buying all of the pieces seperate (it should be alot cheaper).

- I have around $2k to spend on my bone stock 96 GT. it is a dd and i dont want to spray it. I just want to go faster, and have fun doing it.

- If i buy the pieces seperate, i should be able to budget in some aftermarket cams. are the cams worth the money, and if so what kind?

- if i go with a stock p.i. swap, will i need to tune it afterwards. That should run me an additional $400.

any help would be awesome. thanks.

stonegod85 · Apr 26, 2006

peice them together...get some nice used PI heads, intake, and vt n/a cams and a tune. that will probably run you just at $2k and set you at around 280RWHP. then do some common bolt-ons along the way and you should easily hit 300! good luck

the98stang · Apr 26, 2006

The car will not have to be tuned right after the head swap, but should be done within a reasonable amount of time. If you plan on using bigger cams, then the tune is a must.

Miles · Apr 26, 2006

The most expensive piece of what you want to do, I say, would be the aftermarket cams. They'll cost you 1/4 of what you're looking to spend.

You can find used heads for $200, intake for $230 or so, then just buy the actual headswap gasket kit w/ bolts, etc.

Another big Q to answer is will you be doing the install yourself? If not, I doubt you can even get the PI headswap then..

CanadaStang · Apr 26, 2006

Personally, I've always been a little nervous about buying used parts and then just throwing them on. I like to give everything a thorough going over before installing anything used. If you do go that route, you should at least have them checked out by an engine rebuilding shop if your not able to yourself.

96 GT JOE · Apr 26, 2006

i'll be doing this swap with a buddy of mine. what do u guys think of steen racings p&p stage 1 p.i. headswap???
www.steenracing.com

RandyStinchcomb · Apr 27, 2006

96 GT JOE said:
i'll be doing this swap with a buddy of mine. what do u guys think of steen racings p&p stage 1 p.i. headswap???
www.steenracing.com

yup, there's your best-bet

Miles · Apr 27, 2006

CanadaStang said:
Personally, I've always been a little nervous about buying used parts and then just throwing them on. I like to give everything a thorough going over before installing anything used. If you do go that route, you should at least have them checked out by an engine rebuilding shop if your not able to yourself.

That's why i went parkway saving $800 bucks vs. bolting everyone on to find a cracked head...

DropTopPony · Apr 27, 2006

96 GT JOE said:
i'll be doing this swap with a buddy of mine. what do u guys think of steen racings p&p stage 1 p.i. headswap???
www.steenracing.com

very good option!

Gearbanger 101 · Apr 27, 2006

Another question you should ask yourself is, are the power levels of a N/A PI swapped car going to be enough for you later down the road? If not, then you'd better be alright with the nitrous route, since going with a blower/turbo and a 10.4:1 compression ratio (which is what you'll get after the swap) is what you're going to end up with.

That being said, if you plan on really making power, you'll have to pull the heads off and build the short block anyway, in which case you could in fact swap out to lower compression pistons. But you should be easily able to run 400-420+hp without having to do that.....but not with a headswapped compression ratio.

p.i. swap difference?

96 GT JOE

New Member

stonegod85

New Member

the98stang

Active Member

Miles

CanadaStang

New Member

96 GT JOE

New Member

RandyStinchcomb

New Member

Miles

DropTopPony

Noob Slayer

Gearbanger 101

Straight Outta Locash

Similar threads

p.i. swap difference?

New Member

New Member

Active Member

New Member

New Member

New Member

Noob Slayer

Straight Outta Locash

Similar threads

Privacy & Transparency

Privacy & Transparency