• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

rear end advice

  • Thread starter Thread starter billison
  • Start date Start date Mar 22, 2006

billison

I like tinted tail
15 Year Member
Feb 27, 2006
2,607
1,094
184
stl
Mar 22, 2006
#1
  • Mar 22, 2006
  • #1
ok, my rear is junk,

it's the 7.7, stock gears

i don't think the rear brakes were changed for atleast the last 10 years "befor i had it" the best i get out of the rear brakes is fluid to shoot out

what will be the best car to get a rear end out of, looking for the best bang for the buck

also, i'm not wanting to change the master cylender so i'm looking for an alternative to the tourbo coupe rear, but i have to get the rear brakes going for emissions,

it's a 85 auto
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Mar 22, 2006
#2
  • Mar 22, 2006
  • #2
You've got lots of options. My chosen route is an 8.8 out of a 94 with 31 spline trac-loc and Moser axles.
 

ninety15.0

New Member
Mar 10, 2004
1,336
0
0
Mar 22, 2006
#3
  • Mar 22, 2006
  • #3
ive heard u can get complete rear ends out of SVO cars with factory 3.73's and its an 8.8". or you could grab a 99+ axle that comes stock with 3.27's.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 23, 2006
#4
  • Mar 23, 2006
  • #4
ninety15.0 said:
ive heard u can get complete rear ends out of SVO cars with factory 3.73's and its an 8.8". or you could grab a 99+ axle that comes stock with 3.27's.
Click to expand...
The 99 and later rear axles are a lot wider = 1.5" per side. Unless you want to do the ricer ghetto thing with little wheels and have them stick out past the fenders, I wouldn't recommend it.
 
K

kn7671

New Member
Aug 18, 2004
60
0
0
Arlington, TX
Mar 23, 2006
#5
  • Mar 23, 2006
  • #5
I just bought an entirely brand new 8.8" rear-end w/3.73 gears from FMS through Summit. It was around $800 to my door. It comes w/o brakes and axles, but the axles from your stock 7.5" rear-end from your '85 Mustang, and the stock drum brake setup will bolt right up w/o any problems. I know this because I had an '84 Mustang 7 years ago that I had for 4 years and did the same 7.5" to 8.8" rear-end swap on it.

If you plan to keep your car for a long time, do yourself a favor and get a new one, not a junk yarder. If you're short on money, than get a junker, but be careful not to get one with anything bent on it. Plan on at least cleaning out the old fluid, etc. and changing the axles seals and bearings.

When I weighed the options, and the cost of a junker plus replacing seals and bearings, was total was about $450, so for about twice the money I got a new one with not problems or abuse on it yet.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Mar 23, 2006
#6
  • Mar 23, 2006
  • #6
I managed the entire front and rear end out of a 94, all brake components, booster, MC, even the K-member (worthless lol) and e-brake cables... That stuff was $400. The rear end rebuild parts including 31 spline axles and 31 spline trac-loc will cost me another $440. Once complete and ready to install, the whole thing will have cost me roughly $850 for a 4 wheel disk brake conversion with a rear 31 spline setup. I'll toss the other $150 in for a differential girdle from Trick Flow.

Another reason I went this route is that it allows me to weld the axle tubes with no drama.
 

billison

I like tinted tail
15 Year Member
Feb 27, 2006
2,607
1,094
184
stl
Mar 23, 2006
#7
  • Mar 23, 2006
  • #7
i'm on a major budgit right now " just got married" and i'd like to keep it under 2 or 3 hundred so i'm mainly looking at a junk yard rear end, i was wondering about if i cam aross one of the like 4 banger turbo gt's, what about the rears out of them, did'nt they have good gears, i can get a 4 banger rear for basicly free, would that do to just get me through the emissions test, i know it wount last long, but for a temp fix?
 
You must log in or register to reply here.

Similar threads

W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
298
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
P
Engine Mysterious coolant leak at back of engine
  • palerider94
  • Jan 18, 2026
  • Fox 5.0 Mustang Tech
Replies
1
Views
281
Fox 5.0 Mustang Tech Jan 19, 2026
AeroCoupe
Suspension Setting Front Alignment - Do I care about the rear's thrust angle?
  • dan50
  • Nov 27, 2025
  • Fox 5.0 Mustang Tech
Replies
5
Views
429
Fox 5.0 Mustang Tech Nov 28, 2025
Kid wita 5oh
2000 GT-Front Brakes Not Releasing
  • stormsedge
  • Aug 7, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
254
1996 - 2004 SN95 Mustang -General/Talk- Aug 7, 2026
Bronco2fan
B
Progress Thread 91GTstroked 90 7 up convertible build
  • 91GTstroked
  • Apr 18, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
485
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 22, 2026
91GTstroked
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?