runnin really rich!!!

quik50

New Member
Jul 14, 2005
21
0
0
jonesboro, ga
alright guys i am here askin for sum much needed help. i have a 89 lx (originally aod) that i have converted to a t5. i have heard there were sum differences in the comps. from the aod-t5??? when i down shift or get on it really hard it smokes black out the back( tellin me it is runnin rich) but on the top end of the rpm band it quits. now i don't know how tru this is but i have been told that the aod comp. advances timing as it would shift. dont know how tru this is. thanks for your help in advance.
 
bubba-dough said:
You need a 5 spd computer.

no he doesn't, the aod computer will work just fine, been there done that.

I'd start with pulling engine codes, and work from there. Could be anything from fuel pressure regulator to vacuum leaks if you're speed density, etc. I'm hunting down a MEAN run rich condition after my recent engine swap.
 
Dump the codes and see what the computer says is wrong…

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/
OR
See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html

IF your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.

Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Walmart.

Or for a nicer scanner see http://www.midwayautosupply.com/detailedproductdescription.asp?3829 – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $35.
 
fyi, I bought an autozone scanner for my 86 stang, as it didn't have that check engine light. the scanner just plugged right into the plug under the hood, and gave me the beep and lights, no need for an engine light with that thing.
 
quik50 said:
see guys thats tha funniest thing bout my car it is not throwing a check engine light. no codes! it is a 89 lx mass air car.:shrug:
Just because the CEL is not illuminated does not mean there are not codes stored in the KAM. There is a greater threshold to light the CEL than to simply store a code. And since you issue appears to be intermittant or sporadic and does not significantly affect drivablity, per the computer, that fits the profile of a time it might not spit a code.

Tossing codes is always a good idea.

Good luck.
 
thanks for the help guys. it is not an intermittin problem, it does this everyday. it has an adjust. fuel press. reg on it. i need to try checkin the fuel press. what should that be runnin at??? if i remember corectly it should be round 40-32#??? agian thanks for all your help
 
mid to low 30's.

seriously, if you don't start by pulling codes, you're wasting your time.

I almost gaurantee you you have engine codes in there. that check engine light won't always light.
 
quik50 said:
it is not an intermittin problem, it does this everyday.
Intermittant was a poor choice of wording by me. The fact that you mentioned the issue while at WOT but not in other situations means it is not constant. And when something occurs for a short period of time (like at WOT) and then goes away (once you get out of the pedal) is when the puter might not set the CEL. Especially since it does not seem to be seriously hurting the car.
If it was an issue that greatly affected performance, could really hurt the car, or was out of tolerance during all times the engine was operational, that would be more likely to trip the CEL.

As Jeremy said, simulated WOT FP should be ~38-39 PSI stock. And it should be above 30 PSI with the vac line attached.

Good luck.