• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Running Rich?

  • Thread starter Thread starter jrp27540
  • Start date Start date Sep 14, 2016
Prev
  • 1
  • 2
  • 3
First Prev 3 of 3

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Oct 18, 2016
#41
  • Oct 18, 2016
  • #41
If you have 8 wires on the engine harness, you are in better shape. However, you need to locate the correct o2 harness for a manual trans. The jumper can be repinned easily, so don't pass up a good deal on a v8 o2 harness.


Sent from my iPhone using Tapatalk
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Oct 18, 2016
#42
  • Oct 18, 2016
  • #42
Also, the vss code could be from when it wasn't hooked up. Try erasing all codes and re running them.


Sent from my iPhone using Tapatalk
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Oct 18, 2016
#43
  • Oct 18, 2016
  • #43
jrp27540 said:
The date is 02/88.
Click to expand...

Mine is also 2/88, and I have the 8 wire engine harness, and looped o2 harness. Interesting how yours doesn't.


Off topic, but my final vin numbers are 212800. I wonder how far apart our cars are


Sent from my iPhone using Tapatalk
 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 18, 2016
#44
  • Oct 18, 2016
  • #44
Mustang5L5 said:
Mine is also 2/88, and I have the 8 wire engine harness, and looped o2 harness. Interesting how yours doesn't.


Off topic, but my final vin numbers are 212800. I wonder how far apart our cars are


Sent from my iPhone using Tapatalk
Click to expand...

Mine is 216478. Surprise the jump is that high. It's also odd that mine had the 5 wire loop and yours didn't... at least I know now what needs to be done with it. Thanks again for all the help!
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Oct 18, 2016
#45
  • Oct 18, 2016
  • #45
Adding that loop will clear your code 67 and allow you to proceed with dumping engine running codes.

Doesn't solve all your problems, but gets you one step closer.
 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 18, 2016
#46
  • Oct 18, 2016
  • #46
Mustang5L5 said:
Adding that loop will clear your code 67 and allow you to proceed with dumping engine running codes.

Doesn't solve all your problems, but gets you one step closer.
Click to expand...

Ha!...very true statement. At least thanks to you and others on here have helped me build the list of issues so I can prioritize. The nice thing is that all the items on the list are easy and affordable . Looking forward to getting it running better AND knowing things are done correctly.
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,134
10,752
213
polk county florida
Oct 19, 2016
#47
  • Oct 19, 2016
  • #47
Aahh, the happiness of a well wired machine!
 
Reactions: jrp27540

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Oct 19, 2016
#48
  • Oct 19, 2016
  • #48
If you are crafty enough, you can probably add the jumper to the harness you already have.

It all depends on the level of "correctness" you want here.

Best - factory o2 harness wity correct pin

2nd best - repinned factory harness

Perfectly acceptable - modify your harness with a jumper

Ok method - jumper between two wires on engine harness

Hack - cut and splice the two wires



After you get this done, you need to check for voltage on pin 47 on the EEC. You want to do this because you run the risk of frying the EEC. Pull the computer out, set up a multimeter to test pin 47 to ground. Have someone crank engine over. No voltage, good to go. If you have voltage, your pin is wrong and needs to move.

If you am search "mustang o2 harness differences" there are a few good threads. It's not a complicated topic, but you need to pay attention or it can be an expensive mistake


Sent from my iPhone using Tapatalk
 
Reactions: a91what
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 19, 2016
#49
  • Oct 19, 2016
  • #49
Mustang5L5 said:
If you are crafty enough, you can probably add the jumper to the harness you already have.

It all depends on the level of "correctness" you want here.

Best - factory o2 harness wity correct pin

2nd best - repinned factory harness

Perfectly acceptable - modify your harness with a jumper

Ok method - jumper between two wires on engine harness

Hack - cut and splice the two wires



After you get this done, you need to check for voltage on pin 47 on the EEC. You want to do this because you run the risk of frying the EEC. Pull the computer out, set up a multimeter to test pin 47 to ground. Have someone crank engine over. No voltage, good to go. If you have voltage, your pin is wrong and needs to move.

If you am search "mustang o2 harness differences" there are a few good threads. It's not a complicated topic, but you need to pay attention or it can be an expensive mistake


Sent from my iPhone using Tapatalk
Click to expand...

I can definitely add the jumper. I thought about that last night. At least adding it would buy time until I can find the correct harness at a good price.

I have been poking around to find which wires I should jump. Do you know off the top of your head, or know of a thread that would contain that information?

 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 19, 2016
#50
  • Oct 19, 2016
  • #50
jrp27540 said:
I can definitely add the jumper. I thought about that last night. At least adding it would buy time until I can find the correct harness at a good price.

I have been poking around to find which wires I should jump. Do you know off the top of your head, or know of a thread that would contain that information?

Click to expand...

Never mind I found it:

88-90 AOD: jumper from pin 1 bottom row to pin 2 bottom row (as shown in the first picture)
88-90 5 speed: jumper from pin 1 top row to pin 1 bottom row (as shown in the third picture, left connector)

The bad part of the post is that all the pics are gone so I'll have to figure out which side is pin 1.
 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Oct 19, 2016
#51
  • Oct 19, 2016
  • #51
It has to be something like this based on what is open and the pins noted for standard

 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Oct 19, 2016
#52
  • Oct 19, 2016
  • #52
It's pretty easy actually. It's an 8 pin connector ,and you have 5 wires so 3 open spots. 3 pins in one row, and 2 pins in the other.

basically you add the pin to the 4th spot in the row of 3, and then jump it to the pin directly above it.

You don't touch the other 5 wires. You just add a jumper vertically down at the end.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,376
18,123
224
Massachusetts
Oct 19, 2016
#53
  • Oct 19, 2016
  • #53
Yup. Your pic is it. Jump to the pin directly below it
 
J

jrp27540

Active Member
Sep 9, 2016
173
35
38
Mar 19, 2017
#54
  • Mar 19, 2017
  • #54
I wanted to close the loop on this thread just in case someone comes across this thread looking for answers. It has taken several months(lack of time to work on the car), but I FINALLY have made progress on this car. I haven't been able to pull the key on codes since I owned the car. After doing a lot of digging, and re-tracing the previous owners modifications, I found that he did not do the MAF conversion correctly. He forgot to move the tan/red and green/black wires on the EEC. I also added the missing jumper wire on the o2 harness(details outlined above). Once I moved the wires on the EEC, I was able to get the key on codes with no problem. Ends up the code showed that I had a bad coolant temperature sensor, which was causing the car to die and not start after getting to normal driving temp. I have also read that a bad coolant temp sensor will cause the car to run rich. I replaced the sensor and the car no longer dies once at operating temp. It also appears to have resolved the running rich issue as well. Thanks for the help all!
 
Reactions: Mustang5L5
Prev
  • 1
  • 2
  • 3
First Prev 3 of 3
You must log in or register to reply here.

Similar threads

S
Fox '87 GT can't get to stay running
  • spilly
  • Mar 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
27
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 20, 2026
spilly
S
J
i need help
  • JK.
  • Oct 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
22
Views
640
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 28, 2026
JD1964
R
Efi to car pcv HELP !
  • rgrendell
  • Jul 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
737
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 2, 2026
Noobz347
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
320
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
D
Loud noise(s) from Engine Bay
  • DuluthFoxbody
  • Oct 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
387
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 5, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?