Safe to use impact gun removing water pump bolts???

8

89 Saleen#455

Founding Member

Dec 29, 1999

519

5

39

New England

Jun 26, 2005

#1

• Jun 26, 2005

• #1

The gasket is leaking on my original water pump (42K miles), so it's time to swap it out. Can I use an impact wrench to remove the water pump bolts or do I run the risk of snapping a bolt/stud? Obviously I'll use a torque wrench and factory specs. when installing the new pump. I'm also planning to coat all bolts with a liberal dose of antiseize. Any other tips?

 

D

Daggar

New Member

Jul 19, 2004

3,902

5

0

Jun 26, 2005

#2

• Jun 26, 2005

• #2

Nooooooooooo impact gun!

 

z9_87

New Member

Apr 16, 2004

332

0

0

Urbana, IL

Jun 26, 2005

#3

• Jun 26, 2005

• #3

Not unless you like drilling and tapping holes.

 

HISSIN50

"How long does it take to get help in here?

15 Year Member

Nov 29, 1999

31,179

34

129

Jun 26, 2005

#4

• Jun 26, 2005

• #4

third vote for no. I would spray them down with PB before starting and hope they come out. It should not take much torque.

Good luck.

 

stangnutlx

New Member

May 24, 2005

242

0

0

Coventry, RI

Jun 26, 2005

#5

• Jun 26, 2005

• #5

why would you want to do that?
use a ratchet

 

Ranchero5.0

The Voice of Reason

Jan 1, 1999

5,306

0

76

Hagerstown MD

Jun 26, 2005

#6

• Jun 26, 2005

• #6

Again no. In fact if they even start to act like they don't want to come out get a propane torch and heat the block and timing chain cover near the bolt to be removed. Heat it long enough for the paint to burn off and any oil to cook off. You are actually drying out the corrosion between the steel bolt and aluminum timing cover. Then gently work it loose, then tight until it frees up. Takes a little time, but I've seen way too many 'how do I remove a broken water pump bolt' thread.

Jamie

 

TomCat

New Member

Apr 19, 2005

412

0

0

Utah

Jun 26, 2005

#7

• Jun 26, 2005

• #7

Don't do it! I used a breaker bar on mine, and two of the studs busted. Not worth the trouble drilling em out, go with the above suggestions.

 

HISSIN50

"How long does it take to get help in here?

15 Year Member

Nov 29, 1999

31,179

34

129

Jun 26, 2005

#8

• Jun 26, 2005

• #8

That is some very SOUND advice from Jamie. With some bolts like that, I limit myself to a dinky 1/4" ratchet. If it requires more torque/leverage than it can provide, other measures need to be taken (excellent tip with the heating of the fastener).

Good luck.

 

Shakerhood

20+ Year Stangneter

Oct 28, 2004

3,356

208

114

Ohio

Jun 26, 2005

#9

• Jun 26, 2005

• #9

When I changed my pump I traced the new one on a piece of card board and when I removed the bolts, studs I poked them in the cardboard where they came from so when putting the new one on they were ready to go, no way to confuse which one goes where. And NO to the Impact Gun!!!!!!!!!!!!!

 

old_blue

15 Year Member

Nov 3, 2003

1,783

282

124

Jun 27, 2005

#10

• Jun 27, 2005

• #10

no for impact, break them loose with a rachet and then use an air rachet if you want. That is what I do. But I dont think I have ever ued an impact wrench on anything for the motor. Mostly suspension parts and what not.

 

ExplodingGopher

New Member

Jun 11, 2004

517

0

0

The mistake on the lake (Ohio)

Jun 27, 2005

#11

• Jun 27, 2005

• #11

use an air ratchet, not impact gun....

 

8

89 Saleen#455

Founding Member

Dec 29, 1999

519

5

39

New England

Jun 27, 2005

#12

• Jun 27, 2005

• #12

Thanks for the advice guys! I'll refrain from the impact gun and break out the propone torch if necessary. Generally speaking, does the antiseize applied to the factory bolts hold up well on the original pump? Most of the horror stories I've read about snapping bolts seems to surround "replacement" pumps in which the bolts were overtighten beyond factory specs. Any of you guys had problems with removing the "factory bolts" when replacing the pump? Thanks again for all your input!

 

z9_87

New Member

Apr 16, 2004

332

0

0

Urbana, IL

Jun 28, 2005

#13

• Jun 28, 2005

• #13

I had problems with my 3.8 water pump had 120k on it and snapped 1 bolt. Just make sure you use a torque wrench to tighten them.