• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

shortblock question

  • Thread starter Thread starter blown90notch
  • Start date Start date Jan 29, 2009
B

blown90notch

New Member
Oct 16, 2008
14
0
0
Jan 29, 2009
#1
  • Jan 29, 2009
  • #1
a friend of mine has a 5.0 shortblock out of a 94 cobra.first question is:

1: is there anything special about the cobra shortblock compared to a gt shortblock?

2: what would it take to use that shortblock in my 90 coupe,,is there anything i have to change on the block to make it work?

the block in my coupe needs rebuilt,and my friend has this good shortblock.i am trying to compare the cost of rebuilding my block to buying this good shortblock and what it takes to make it work in a fox.

any thoughts on this would be highly appreciated.
mark
 

Evilfox

New Member
Dec 2, 2008
45
0
0
Elk Grove, Ca
Jan 29, 2009
#2
  • Jan 29, 2009
  • #2
It's the same block. Nothing special about the short block. Only differences were GT40 heads instead of E7's, 1.7 roller rockers, the cobra intake, 24lbs injectors vs the GT's 19's. That's really it.
 
B

blown90notch

New Member
Oct 16, 2008
14
0
0
Jan 29, 2009
#3
  • Jan 29, 2009
  • #3
so i should be able to just bolt my parts from 90 on the short block and be good?sweet!of course i have twisted wedge heads, and anderson ford motorsport cam and some other goodies for it.oh and a paxton supercharger.
 

Evilfox

New Member
Dec 2, 2008
45
0
0
Elk Grove, Ca
Jan 29, 2009
#4
  • Jan 29, 2009
  • #4
Yep. Just make sure if you reuse your old cam you match the pushrods, lifters, and rockers to the lobes they came off of.
 
B

blown90notch

New Member
Oct 16, 2008
14
0
0
Jan 29, 2009
#5
  • Jan 29, 2009
  • #5
i have to get new push rods,and the heads are in the machine shop getting totally rebuilt.damn valve guide problems.i bought the car with the problems and am just getting around to fixing it.as far as lifters go,they are still in the block with the cam so i should be good with lining them up.i didnt think it mattered as much with the roller cam motors as far as putting the lifters back on the same lobe.maybe i am wrong.
 

Evilfox

New Member
Dec 2, 2008
45
0
0
Elk Grove, Ca
Jan 29, 2009
#6
  • Jan 29, 2009
  • #6
Each lifter wears to the side of a cam lobe differently. The differences get more and more drastic with the more miles you put on the cam.
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Jan 30, 2009
#7
  • Jan 30, 2009
  • #7
With an HR camshaft, lifter/lobe wear is nothing compared to the old flat tappets. Many have mixed and matched lifters to different lobes on a HR camshaft with no problems.

The camshaft is different between the Cobra and LX/GT blocks.
 

millhouse

Founding Member
May 14, 2002
1,985
0
46
Simpsonville, SC
Jan 30, 2009
#8
  • Jan 30, 2009
  • #8
5spd GT said:
With an HR camshaft, lifter/lobe wear is nothing compared to the old flat tappets. Many have mixed and matched lifters to different lobes on a HR camshaft with no problems.

The camshaft is different between the Cobra and LX/GT blocks.
Click to expand...

+1....mixing and matching isn't an issue with HR setups.

One more difference which may or may not be relevant to you, but your stock 90 shortblock comes with forged pistons while your friends has hypereutectic. Forged is only really a benefit if you were to run nitrous or a forced induction setup...as they hold up to detonation far better than their hyper counterparts. That's not to say they won’t hold up under boost....you just need to make sure your tune is spot on.
 
B

blown90notch

New Member
Oct 16, 2008
14
0
0
Jan 30, 2009
#9
  • Jan 30, 2009
  • #9
that is a good point.my car has a paxton on it,its only 6psi so it may not make to much difference.

my thoughts are to get this shortblock so i can get the car running,then build the 90 shortblock and maybe even put a stroker kit in it for later.who knows. thanks for the advice!
 
B

blown90notch

New Member
Oct 16, 2008
14
0
0
Jan 30, 2009
#10
  • Jan 30, 2009
  • #10
i went ahead and bought the shortblock for $100.00.
 
You must log in or register to reply here.

Similar threads

Electrical Lincoln Mark VIII Replacement Fan Motor
  • AeroCoupe
  • Sep 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
166
Fox 5.0 Mustang Tech Sep 26, 2026
AeroCoupe
Ford truck engine swap issues
  • keel
  • Jul 7, 2026
  • Other Auto Tech
Replies
17
Views
765
Other Auto Tech Jul 13, 2026
General karthief
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
2003-04 Mustang Cobra Brake Conversion
  • Cassiebaebae
  • Oct 8, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
258
1996 - 2004 SN95 Mustang -General/Talk- Oct 24, 2026
Bib36`
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?