SON OF A BISCUIT!!!

[dcurtis]

If you did swap to the standard offset arms it would only pull your wheels back 3/4 of an inch, as that is the difference between the standard and forward offset arms. I think you have other problems, with the k member and the forward offset arms you should only be 1 and 1/2 inches farther forward than stock. Hope you figure out the prob, good luck.

 

[Mustang5L5]

That;s what i read too. That looks like a hell of a lot more than 1.5 inches.

It doesn't look right at all.


Stupid question, but are the arms upside down? Can they be flipped over and used that way?

 

[Shaolin Crane]

That;s what i read too. That looks like a hell of a lot more than 1.5 inches.

It doesn't look right at all.


Stupid question, but are the arms upside down? Can they be flipped over and used that way?

No the can only be installed one way on the car, and i think you ment are they on the wrong side, if the were upside down my coil overs would be pointing down

 

[Blandnuts]

They're being awfully nice on cc. Jack should be able to give some hints on to which arms you have. Your pics looks similar to pics I've seen on cc or corral with kmembers and offset arms. They were also running different size tires. I'll see if I can find that thread.


Fred

 

[Shaolin Crane]

yeah they are being nice, must be from mothers day or something

 

[GT_Rich]

You could dismount the tires and then set the rims on the dollies and roll it out.

 

[1991vert]

do you have the a-arms reversed? like pass side on drivers and drivers on pass? granted the sway bar mount holes would not line up, but maybe you arent running a sway bar? that offset is absolutely crazy

 

[Shaolin Crane]

i feel like a total tard, i went looking through my invoices to be certain that i had standard offset arms, turns out i got the forward offsets, damn that was a while ago over a year now, anywho at least im getting the car back togethor and i have some serious castor to play with

 

[Mustang5L5]

So you gonna stick with them or change them?

 

[dcurtis]

Standard arms will only move the wheel back 3/4 of an inch, it will give you clearance to move the car but the wheel will still be too far forward it would seem.

 

[Shaolin Crane]

So you gonna stick with them or change them?

im gonna stick with them, it may not look pretty now but its gonna handle bitchen and thats all that really matters, im just gonna buy some fenders that are flared and offset

 

[LiquidGT]

im gonna stick with them, it may not look pretty now but its gonna handle bitchen and thats all that really matters, im just gonna buy some fenders that are flared and offset

I was gonna post earlier and say make some offset fenders as joke; if you did that then the front would be similar to the FR500.

 

[Shaolin Crane]

I was gonna post earlier and say make some offset fenders as joke; if you did that then the front would be similar to the FR500.

i actually like the way that those look, but damn the are pricey

 

[LiquidGT]

I believe they only made one FR500, so I guess it would be pricey... or are you talking about the rims?

 

[Shaolin Crane]

I believe they only made one FR500, so I guess it would be pricey... or are you talking about the rims?

no i ment the similar fenders for the foxes that offset the wheel hole

 

[Mustang5L5]

They have those?

 

[Shaolin Crane]

They have those?

yeah and they are expensive

 

[stykthyn]

yeah and they are expensive

linkey?

 

[Shaolin Crane]

Inertia Sport Maier Racing Fender Flares for the Mustang Coupe

 

[Mustang5L5]

Damn, $640/pair!