Spoilered trunk lid and end caps for 65.

65fastbackresto · May 2, 2011

Looking for good quality parts that hopefully wont cost me a fortune to fit at the body shop. I assume fiberglass is the only way to go, but I am not sure, any advice on quality parts will be greatly appreciated.

And, long time no see guys, I haven`t toyed with my car in couple years, but I`m back and you`ll be seeing alot of me again.

rbohm · May 2, 2011

most of the companies you are going to deal with use fiberglass for things like that. if you have some fab skills, you can make your own though.

robbz28 · May 2, 2011

I purchased mine for my 67 from mustangs unlimited...Im not sure who they use, but the lid is a quality piece...the endcaps fit like pure crap, but I have been told thats the story with all of them, I fit them as best as I could with my limited fiberglass skills, in fact ruined one, had to order another one, this time from CJ pony, and it too fit like crap, it took a complete reworking by a body man to get them right. he had to cut them, add fiberglass here and there, lots of fiberglass filled bondo, but they came out really really nice.

65fastbackresto · May 6, 2011

Ok, got my first ever peice of fiberglass today.

Its a Shelby R style front valance made by Dynacorn that looks alot more like injection molded plastic then fiberglass to me. It has a smooth finish inside and outside, and just a little wave or 2 in the front of it. Is this what it should look like?...

I can send a pic or 2 later when my wife gets home if need be.

robbz28 · May 6, 2011

They make both a plastic and a fiberglass version....sounds like you got a plastic one. I know on ebay you can see both versions, when you order from a catalog, not sure if they tell you what the material is.

65fastbackresto · May 7, 2011

Should I keep it if its plastic?

robbz28 said:
They make both a plastic and a fiberglass version....sounds like you got a plastic one. I know on ebay you can see both versions, when you order from a catalog, not sure if they tell you what the material is.

I really thought I was getting a higher quality part then this anyway.

65fastbackresto · May 12, 2011

Has anyone used this brand of fiberglass?

65 - 66 Mustang Fastback Shelby Style Deck Lid: Fiberglass &amp Deck Lids

I like the fact the hardware is already on these pieces. My body man seemed to think this may be superior workmanship to some of the other stuff, you guys give me some input please?

robbz28 · May 12, 2011

The ones I purchased had the hardware attached to them as well, like mentioned earlier, the deck lid was a quality piece. The end caps were total crap, but they too had the mounting hardware....it had to be removed and reworked and replaced, but it had them anyway. I would almost guarantee that they ones I bought and the onese these guys have came from the same place...

65fastbackresto · May 12, 2011

This vendor is also the manufacturer

I think you would have to buy directly from them to get their parts, I`ve never seen them in a catalog or anywhere else....

65fastbackresto · May 12, 2011

Jims Classic and Hot Rod fiberglass is the manufacturer actually, they make them for Stangaholics.

robbz28 · May 12, 2011

I was just happy that the body man that is painting my car is an expert with fiberglass, he really made them look good and fit properly. Everything had to be fitted. I even got a glass hood with the metal frame (dynacorn) and it was 1/2" too long...he had to shave that off of the rear of the hood to make it fit right. Fiberglass is rarely ever going to bolt right on unless its an OEM piece. If you are patient and have a little knowledge of body work you can fit those pieces, or if you are like me and lazy you can pay someone, lol.

65fastbackresto · May 12, 2011

LOL, I aint no fiberglass worker either.

I`m pretty sure I`d just ruin the parts trying to put them on, so I`m paying someone too.

My dynacorn shelby R valance I mentioned earlier in this posting fits pretty bad in my opinion, its about 1/2 inch too short, I think my body man can fix it though.

And yes, "aint" is proper grammer in arkansas...

65fastbackresto · May 27, 2011

Yea the parts truck finally ran!!!!!

I got my decklid and endcaps today from Stangoholics, these things look awesome, the quality of the glass is incredible. I`ll get some pics up when I try and fit them tommorow.

65fastbackresto · May 31, 2011

Need a little help here.

Anyone that has done the spoiler deck lid conversion, will this part and the old hardware off the old trunklid make it where I can open my trunk?

64-66 Remote Trunk Release: Trunk Compartment &amp Trunk Release

They also have an electric one.

65 - 66 Mustang Electric Trunk Release Kit: Keys, Locks Latches &amp Electric Trunk Release Kit

Red5oh · May 31, 2011

I got mine from Branda. The trunk is a factory vacuum formed piece and it is wonderful. The extensions were another story, but they were VERY clear that it would be some work to get it to fit. I have a few pics on the website listed below, and feel free to ask questions

65fastbackresto · Jun 1, 2011

I love that website, good work

But do you know anything about the remote trunk release? Is it routed thru the trunk lid?

Spoilered trunk lid and end caps for 65.

65fastbackresto

Active Member

rbohm

robbz28

65fastbackresto

Active Member

robbz28

65fastbackresto

Active Member

65fastbackresto

Active Member

robbz28

65fastbackresto

Active Member

65fastbackresto

Active Member

robbz28

65fastbackresto

Active Member

65fastbackresto

Active Member

65fastbackresto

Active Member

Red5oh

Member

65fastbackresto

Active Member

Similar threads

Spoilered trunk lid and end caps for 65.

Active Member

Active Member

Active Member

Active Member

Active Member

Active Member

Active Member

Active Member

Active Member

Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency