• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Started header install, removing hoses??

  • Thread starter Thread starter Rynb15
  • Start date Start date Jun 3, 2006

Rynb15

Member
Nov 21, 2005
132
2
18
Jun 3, 2006
#1
  • Jun 3, 2006
  • #1
So i started the header install. Got everything off but it was a pain in the ass. The stock h pipe had to be cut off it was rusted so bad. Anyways on the new h pipe going on(actually used) the tube for the smog pump is smashed shut. So what should i do with that part that runs back up to the engine? Also the other black hoses in the same area that all connect together by the passenger side header i disconnected during the process. Should i put them back together? I really have no idea what they are. Is there a way to get rid off it all if it does not have to be there?
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Jun 4, 2006
#2
  • Jun 4, 2006
  • #2
It sounds like you are talking about the smog pump lines. If your new midpipe does not have cats, AND you will not have to pass emissions testing, then it will be fine to remove the air pump and the associated lines. There are a couple of vac lines in this system, so be sure to cap them off.

Good Luck
jason
 

Rynb15

Member
Nov 21, 2005
132
2
18
Jun 4, 2006
#3
  • Jun 4, 2006
  • #3
thanks for the info. What if i leave all the hoses there. What to i do with the one to the h pipe? Cap it?
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Jun 4, 2006
#4
  • Jun 4, 2006
  • #4
i pounded a big bolt into it. but capping it would work aswell.
 

Rynb15

Member
Nov 21, 2005
132
2
18
Jun 4, 2006
#5
  • Jun 4, 2006
  • #5
thank you
 

sn9550

Founding Member
May 13, 2000
1,184
1
37
Charles Town, WV
Jun 4, 2006
#6
  • Jun 4, 2006
  • #6
If you can cut the smashed part of the tube off (of the H pipe) and you still have some left use 3/4" heater hose to connect it back.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Jun 4, 2006
#7
  • Jun 4, 2006
  • #7
Rynb15 said:
thanks for the info. What if i leave all the hoses there. What to i do with the one to the h pipe? Cap it?
Click to expand...

I wouldn't recommend capping that hose unless you have already removed the air pump.
Capping that line with the pump in place will burn up the pump very quick.

jason
 
T

tbi92rs

New Member
Sep 2, 2005
69
0
0
Louisville, KY
Jun 4, 2006
#8
  • Jun 4, 2006
  • #8
I welded my X-pipe tube shut. As for the lines form the back of the head, i took the off, chopped them off, took a hammer (mini-sledge) and beat it shut, then had it welded up by a local muffler shop for 2.50

good luck, it makes everything CLEAN without that smog junk.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jun 4, 2006
#9
  • Jun 4, 2006
  • #9
Here’s some help (a bit late in your case) for removing the air tube from the H pipe...

Try removing the bolts from the upper mounting bracket at the rear of the engine, and then loosen the clamp on the air tube by the cats. Then get a BIG pair of ViseGrip pliers (you really didn't hear me say that), clamp down hard on the tube about 1 1/2" from the clamp and pound away on the ViseGrips. It will come off if you keep at it.

In really stubborn cases, drill a 1/8" hole all the way thru the air tube 1 1/2" from the clamp, put a nail, pin punch or whatever in the hole, seat the ViseGrips up against the nail or pin punch and pound away on the ViseGrips. This is a better method, as you can do the same thing in reverse to put the old tube back on, with some clever means to cover or fill the hole (weld, braze, sheet metal screws, hose clamps and hi temp hose, etc.).

A replacement air tube cost me $44 at Advance Discount Auto Parts, plus the air check valve didn't come with it - another $17, so reuse when and where possible if your money is limited.
 
You must log in or register to reply here.

Similar threads

Problems after exhaust install and 02 harness
  • djj62478
  • Jul 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
39
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
G
Resolved Smoking Wiring Issue After GT40 Head Swap
  • Grapes
  • Aug 15, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
606
Fox 5.0 Mustang Tech Aug 22, 2026
Grapes
G
T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
220
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
F
Fox 1990 Mustang GT 5.0 A9L – Engine suddenly shuts off but immediately restarts when key turned
  • FishermansFriend
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
695
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?