• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

t5 assembly

  • Thread starter Thread starter rockyracoon
  • Start date Start date Feb 24, 2006
R

rockyracoon

10 Year Member
Nov 23, 2005
874
27
49
margate NJ
Feb 24, 2006
#1
  • Feb 24, 2006
  • #1
I have been tryin to get the top cover on my t5 correctly for hours, I have everything in neutral but when I try putting the cover on and engage the shift forks, it seems that the synchro sleeve towards the output shaft ,the 1st and 2nd doesnt seem to line up with its corresponding shift fork, the sleeve seems too far towards the front of the trans,however if I engage 1st gear by sliding the sleeve rearward the forks will go into place and I can install case cover but the trans will not shift.I dont get it ,the T-5 rebuild manual acts like its no big deal to install the top cover.I have the projection in the notch on the ist and 2nd gear selector plate like the manual says. am I missing something?
 

Bad92GT

The 5 Minute Plan Man
Jun 10, 2004
492
0
0
SC
Feb 24, 2006
#2
  • Feb 24, 2006
  • #2
i've built a few T5's.. the top plate can be tricky sometimes, check to make sure all the pieces are correct. I had one that the forks actually shifted and moved around somehow and i couldnt use it like it was, had to get another to only find out all i needed was to pull it apart real quick. Good luck with it
 

88gt

Founding Member
Aug 2, 1999
794
0
0
Drillers cabin
Feb 24, 2006
#3
  • Feb 24, 2006
  • #3
Are you absolutely positive that the gears are in neutral themselves? Mine moved around a bit on me just enough to make me stop for a minute to make sure I was lined up correctly.

Take a break, have a beer and give it another try..

Jim
 
R

rockyracoon

10 Year Member
Nov 23, 2005
874
27
49
margate NJ
Feb 25, 2006
#4
  • Feb 25, 2006
  • #4
Ok my prob was,The 1st and 2nd collar/slider fork was not going far enough towards the mechanism in the center,therefore everytime i tried to install the cover that slider would move out of neutral all the way into 1st.thanx much fellas
 
You must log in or register to reply here.

Similar threads

Drivetrain How much resistance, if any at all, is normal on a new 1st gear and synchro on a WC T5 transmission?
  • sleep-e
  • Jan 21, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
346
Fox 5.0 Mustang Tech Jan 22, 2026
sleep-e
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
328
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
T5 5th gear 89 gt
  • mac_55
  • Mar 19, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
280
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 20, 2026
Mustang5L5
3
Hammer shifter problems
  • 387lx
  • Apr 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
266
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 11, 2026
General karthief
C
Drivetrain T-5 transmission issue
  • Ch3No2
  • Jul 11, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
493
Fox 5.0 Mustang Tech Jul 18, 2025
2000xp8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?