T5 SWAP DONE!!!!! CAR WONT START??? HELP

Neutral safety switch???

I just completed a 2.3L auto to 5.0L stick swap. I just fired the car up today. What I did, was use the trans harness from the stick car, because there are more wires from that stick harness than the auto harness. Also, there are two plugs that go to the left side of the clutch pedal box, and one plug that goes to the right side of the clutch pedal box. They are all there on automatic dash harnesses, they are just taped up. One more thing...did you get a stick computer??? They ARE different.

OK, Hmmmm....What did you do to prepare for the swap....did you disconnect anything? Is the fuel pump running? Is the coil wire hooked up...I know sounds stupid but it usually is something stupid! Try and retrace your steps....let me know what you figure out...

Why would you completely remove the dash? That makes no sense. It takes tops 2 hours to change pedals by just dropping the steering column. Patience my friend, patience.

Georgie said:

WHATS THE RED BUTTON IN THE TRUNK...DOES IT HAVE ANYTHING TO DO WITH FUEL??? CUZ I UNPLUGGED A BUNCH OF WIRES WHEN I WAS SANDING THE TRUNK AREA

Click to expand...

dude, thats the inertia switch. it cuts off the fuel pump in case of impact (accident). if its not plugged in, you'll have no fuel.

RBRANDX said:

Neutral safety switch???

Click to expand...

If that was it .... it wouldn't even turn over.




Yeah, check that switch in the trunk that you were referring to.

Georgie said:

WHATS THE RED BUTTON IN THE TRUNK...DOES IT HAVE ANYTHING TO DO WITH FUEL??? CUZ I UNPLUGGED A BUNCH OF WIRES WHEN I WAS SANDING THE TRUNK AREA

Click to expand...

yep i would say thats your problem. car will crank you said but not start. plug those back in and it should fire up for you.

Follow this list & don't skip any steps. You will find the problem & fix it. I have better than 95% success rate with it.

Cranks OK, but No Start Checklist for Fuel Injected Mustangs

1.) Remove push on connector from starter solenoid and turn ignition switch on. Place car in neutral or Park. Remove coil wire from distributor & and hold 3/8” away from engine block. Jumper the screw to the big bolt on the starter solenoid that has the battery wire connected to it. You should get a nice fat blue spark.
Most of the items are electrical in nature, so a test light, or even better, a voltmeter, is helpful to be sure they have power to them.
No spark, possible failed items in order of their probability:
A.) MSD or Crane ignition box if so equipped
B.) Coil
C.) TFI module
D.) PIP sensor in distributor
E.) ECC relay next to computer - look for 12 volts at the fuel injector red wires
F.) Fuse links in wiring harness - look for 12 volts at the fuel injector red wires. All the fuse links live in a bundle up near the starter solenoid.
G.) Ignition switch - look for 12 volts at the ignition coil red/lt green wire.
H.) Computer

See the following links for wiring diagrams...

http://www.autozone.com/servlet/UiB..._us/0900823d/80/16/71/3c/0900823d8016713c.jsp for 79-88 model cars

http://www.autozone.com/servlet/UiB..._us/0900823d/80/19/59/5a/0900823d8019595a.jsp for 89-93 model cars

http://www.autozone.com/servlet/UiB..._us/0900823d/80/1d/db/3c/0900823d801ddb3c.jsp for 94-98 model cars


2.) Spark at coil wire, pull #1 plug wire off at the spark plug and check to see spark. No spark, possible failed items in order of their probability:
A.) Moisture inside distributor – remove cap, dry off & spray with WD40
B.) Distributor cap
C.) Rotor
D.) Spark Plug wires
E.) Coil weak or intermittent - you should see 3/8" fat blue spark with a good coil

3.) Spark at spark plug, but no start.
Next, get a can of starting fluid (ether) from your local auto parts store: costs a $1.30 or so. Then pull the air duct off at the throttle body elbow, open the throttle, and spray the ether in it. Reconnect the air duct and try to start the car. Do not try to start the car without reconnecting the air duct.
Two reasons:
1.) If it backfires, the chance for a serious fire is increased.
2.) On Mass Air cars, the computer needs to measure the MAF flow once the engine starts.
If it starts then, you have a fuel management issue. Continue the checklist with emphasis of fuel related items that follow. If it doesn’t, then it is a computer or timing issue: see Step 4.

Clue – listen for the fuel pump to prime when you first turn the ignition switch on. It should run for 5-20 seconds and shut off. To trick the fuel pump into running, find the ECC test connector and jump the connector in the lower RH corner to ground. . See the above graphic for a description of the test connector. If the relay & inertia switch are OK, you will have power to the pump. Check fuel pressure – remove the cap from the schrader valve behind the alternator and depress the core. Fuel should squirt out, catch it in a rag. Beware of fire hazard when you do this. In pinch you can use a tire pressure gauge to measure the fuel pressure. It may not be completely accurate, but you will have some clue as to how much pressure you have.

No fuel pressure, possible failed items in order of their probability:
A.) Tripped inertia switch – Coupe & hatch cars hide it under the plastic trim covering the driver's side taillight. Use the voltmeter or test light to make sure you have power to both sides of the switch
B.) Fuel pump power relay – located under the driver’s seat in most stangs built before 92. On 92 and later model cars it is located below the Mass Air Flow meter. Look for 12 volts at the Pink/Black wire on the fuel pump relay.
C.) Clogged fuel filter
D.) Failed fuel pump
E.) Blown fuse link in wiring harness. Look for 12 volts at the Orange/Lt Blue wire on the fuel pump relay. The fuse links live in the wiring harness near the starter solenoid.
F.) Fuel pressure regulator failed. Remove vacuum line from regulator and inspect for fuel escaping while pump is running.

Fuel pressure OK, the injectors are not firing.

A.) A Noid light available from Autozone, is one way to test the injector wiring.
B.) I like to use an old injector with compressed air applied to the injector where the fuel rail would normally connect. I hook the whole thing up, apply compressed air to the injector and stick it in a paper cup of soapy water. When the engine cranks with the ignition switch on, if the injector fires, it makes bubbles. Cheap if you have the stuff laying around, and works good too.

a.) Pull an injector wire connector off and look for 12 volts on the red wire when the ignition switch is on.
b.) No power, then look for problems with the 10 pin connecter (salt & pepper shakers at the rear of the upper manifold).
c.) No power and the 10 pin connections are good: look for broken wiring between the orange/black wire on the ECC relay and the red wire for the 10 pin connectors.


4.) Spark & fuel pressure OK.

A.) Failed IAB (no airflow to start engine). Press the throttle ¼ way down and try to start the car.
B.) Failed computer (not very likely)
C.) Engine ignition or cam timing off: only likely if the engine has been worked on recently).
D.) Firing order off: HO & 351 use a different firing order from the non HO engines.
HO & 351W 1-3-7-2-6-5-4-8
Non HO 1-5-4-2-6-3-7-8
E.) No start when hot - Press the throttle to the floor & try starting it if you get this far. If it starts, replace the ECT.

Georgie said:

O0HHH BY THE WAY THE COMPUTERS R NOT DIFFERENT

Click to expand...

The computrs between automatic and manual cars are different. You should be fine because an automatic computer can be used in a stick but not the opposite way around.

Try it either way...if you depressurized the fuel lines it should still fire after a few seconds of cranking.
Crank for a few seconds...see if there is fuel at the shrader valve, and just for fun check if theres spark just incase the fuel cut off wasn't your problem.