• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Taking out rearend!! Help!!!

  • Thread starter Thread starter marine_2003
  • Start date Start date Sep 18, 2005

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Sep 18, 2005
#1
  • Sep 18, 2005
  • #1
I need anyone that can help me. I am getting ready to take out the rearend of my mustang to get it ready and prepped so when i sell my 347 stroker kit i can buy the parts that i need to redo my rearend, and get it degreased and prepped to go to the shop once i get all the parts i need. Had anyone taken out the rear before? Can anyone offer tips on how to go about this? I have stock drum brakes, upper and lower control arms, springs shocks, i know i need to disconnect all those and the brake lines.

Thank You for your help
 

fox racer

Member
Jun 22, 2004
577
0
16
Staten Island, NYC
Sep 18, 2005
#2
  • Sep 18, 2005
  • #2
nope never been doen... to do it: disassemble the brakes and disconnect the e brake, then unbolt the shocks from the rear, followed by the driveshaft. remvoen the 4 bolts that hold the stock control arms to the body and pul the rear out the back.
 

accidentprone86

New Member
Apr 1, 2005
189
0
0
Westminster Colorado
Sep 18, 2005
#3
  • Sep 18, 2005
  • #3
Definatly do the drive shaft first. Leave the car in gear and have a buddy push the brake down so you can get enogh force to brake the bolts lose.

Disconect brakes.

Now get a jack "preferably a harly davidson jack" And take the pressure off of the connecting points by lifting up the housing a little, with the car supported by jack stands.

Now remove the sway bar and disconect the lower controls then shocks then uppers and finaly lower the housing down most of the way and then disconnect the quad shocks.

I say disconnect the quads last cuz they will move with the axle but if the rear falls off the jack they will not only slow the fall but not let it go all the way to the ground.
doing this saved me from getting crushed when i did my'n.

Good luck!! And the best of Patience to you!!
Your two best friends while doing this WILL be a propane torch and a impact wrench.
 

accidentprone86

New Member
Apr 1, 2005
189
0
0
Westminster Colorado
Sep 18, 2005
#4
  • Sep 18, 2005
  • #4
Also when you put the springs back in make SURE you seat them right. other wise your car will not sit at the right hight.

The very ends of the coils on the bottm of the springs need to face the drivers side of the car.

I did not do this right the first time and my rear sat a inch higher then stock.
 

marine_2003

Member
Jun 6, 2005
427
0
16
Lake County, FL
Sep 18, 2005
#5
  • Sep 18, 2005
  • #5
So where the coil ends at the tip where its cut at the factory needs to face the drivers side of the car? Is that for both sides?
 

accidentprone86

New Member
Apr 1, 2005
189
0
0
Westminster Colorado
Sep 18, 2005
#6
  • Sep 18, 2005
  • #6
yes that is for both sides of the car.

For installation reverse the take off order.
Do Quads, Uppers, shocks, then lowers.
do the lowers last so the rear end can hang from the car and you can use your jack to compress the spring and piviot the lowers into place to bolt up to the rear.
 

Modular2v

Founding Member
Jun 30, 2002
3,222
23
99
oklahoma
Sep 18, 2005
#7
  • Sep 18, 2005
  • #7
its really really easy
 
You must log in or register to reply here.

Similar threads

W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
291
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
H
97 cobra maf sensor help
  • Hopper1979
  • Oct 16, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
154
1996 - 2004 SN95 Mustang -General/Talk- Oct 17, 2026
CAMTWO1070
J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
334
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
S
Best place to source power steering parts for a '67? (control valve, ram, hoses)
  • SophiaTatum
  • Jun 15, 2026
  • Classic Mustang Specific Tech
Replies
2
Views
218
Classic Mustang Specific Tech Jun 18, 2026
SophiaTatum
S
C
Help with manual conversion
  • CPH89LX
  • Aug 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
694
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 27, 2026
2000xp8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?