• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Tdc Confusion

  • Thread starter Thread starter sen2two
  • Start date Start date Nov 20, 2016

sen2two

I've been lubing and pulling it all morning
5 Year Member
Jul 18, 2013
396
58
59
Nov 20, 2016
#1
  • Nov 20, 2016
  • #1
I am just trying to make sure I'm doing it right since there's a whole lot of misinformation out on the internet about doing this correctly. I do not have any fancy tools to find TDC and I am setting the Lash on newly installed roller rockers.

If I'm doing this correct, both valves on cylinder 1 are closed, air pushes out of the spark plug hole, and my pointer on the balancer should be a zero?
 

TOOLOW91

If you're the village idiot what's that make me?
20+ Year Stangneter
Nov 29, 1999
8,501
8,763
234
S.I.NY
Nov 20, 2016
#2
  • Nov 20, 2016
  • #2
sen2two said:
I am just trying to make sure I'm doing it right since there's a whole lot of misinformation out on the internet about doing this correctly. I do not have any fancy tools to find TDC and I am setting the Lash on newly installed roller rockers.

If I'm doing this correct, both valves on cylinder 1 are closed, air pushes out of the spark plug hole, and my pointer on the balancer should be a zero?
Click to expand...
Thats correct. When the air rushes it may not point to exactly zero on the balancer. I usually then roll it forward or backward to sit directly on zero. Never had an issue this way. Hope that helps.
 

Jersey Joe

I remember blowing that Monkey's ass
10 Year Member
Nov 29, 1999
767
1,319
154
Bloomingdale N.j.
Nov 20, 2016
#3
  • Nov 20, 2016
  • #3
Make that two it works for, just put your finger over the hole till it tries to blow it off.
 

JD1964

there is enough sticking out to grab on to
15 Year Member
Jun 28, 2013
3,637
1,658
194
Maryland
Nov 21, 2016
#4
  • Nov 21, 2016
  • #4
Here's another fool proof easy way to make sure a particular lifter is on base of cam and ready for adjustment.

Rotate the crank until a pushrod is all the way up (fully open). At this point, the opposite lifter for that same cylinder is on the base of the cam and ready for adjustment.

Before you rotate again, look around because another one somewhere on the engine is also in position probably. Rotate the engine and continue.

I tag each rocker with a piece of blue tape to mark as done and proceed until all are done.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Nov 21, 2016
#5
  • Nov 21, 2016
  • #5
Simple and cheap method.

TDC location process courtesy of Michael Yount
If you're trying to find ACTUAL tdc for cam installation/degreeing, follow the steps below:

Positive stop – obtain an old spark plug for the Ford engine – most of us have at least one laying around. Put it in your vice, and with a tool of destruction you deem appropriate – cut off the ground tip and bust up the ceramic around the center electrode. Keep pounding to get the ceramic and center electrode removed so you’ve got a good ¾” or so of hollow space inside what used to be the ‘business’ end of the spark plug. If you happen to break the ceramic on the other end of the spark plug, don’t worry about it. Once you’ve got a nice hollow space in the tip of the plug, take a 5/16” tap, and cut threads inside that end of the plug. I found that diameter to go right in without any drilling required. Once you’ve cut threads, screw in a 5/16" bolt about 1.5” to 2” long. Then take your hack saw and cut the head off the bolt. Wouldn’t hurt to take your file/grinder and dress up the freshly cut surface so no sharp edges or shrapnel enter the combustion chamber. Also clean up the threads on the plug so that it easily screws into and out of the plug hole.

Determining TDC – remove the passenger side valve cover. Rotate the engine (socket on crank bolt) until the #1 piston is down the cylinder on the intake stroke. Unscrew the spark plug in that cylinder, and replace it with the positive stop you just made. Only screw the positive stop in hand tight. Install your cam degree wheel and pointer (no easy task in some cases as harmonic balancer and other accessories will have to be removed). You may want to remove all spark plugs at this point because it will make it easier to smoothly turn the engine over in small increments. GENTLY rotate the engine clockwise until the piston comes to rest against the stop. Note the degree wheel reading. GENTLY rotate the engine in the opposite direction until the piston comes to rest against the stop. Note the degree wheel reading. TDC is exactly half way between these readings. Calculate where that position is on the degree wheel, remove the piston stop from the cylinder, and rotate the engine to TDC as you calculated it.
 
Reactions: Davedacarpainter
You must log in or register to reply here.

Similar threads

H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
622
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
Considering widening my rear wheels, would like to verify my thoughts on fitment
  • 2000xp8
  • Jul 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
37
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 18, 2026
AeroCoupe
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
474
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
S
Timing chain, guides and tensioner installation (Possible orientation in Intake Stroke)
  • StallionMax
  • Sep 21, 2025
  • SN95 4.6L Mustang Tech
Replies
2
Views
533
SN95 4.6L Mustang Tech Sep 24, 2025
StallionMax
S
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?