• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Engine Throttle Body Stock In Close Position On 1989

  • Thread starter Thread starter Jean-Francois
  • Start date Start date May 23, 2013

Jean-Francois

New Member
May 23, 2013
6
0
1
Victoria
May 23, 2013
#1
  • May 23, 2013
  • #1
Hi, I just reset my TPS at .9volt and now my TB is stock close, I have to kit the gas pedal every time I start the engine. Anybody know what should I do.

Thanks
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
May 23, 2013
#2
  • May 23, 2013
  • #2
TB is supposed to be closed at idle. there is a hole in the plate to let air through and you also have the Idle Air Cylenoid that opens and closes to let air in. You either have a fuel issue or your IAC is stuck(pretty common). Have you pulled any codes?
 

Jean-Francois

New Member
May 23, 2013
6
0
1
Victoria
May 23, 2013
#3
  • May 23, 2013
  • #3
stykthyn said:
TB is supposed to be closed at idle. there is a hole in the plate to let air through and you also have the Idle Air Cylenoid that opens and closes to let air in. You either have a fuel issue or your IAC is stuck(pretty common). Have you pulled any codes?
Click to expand...
I have a code 32 for the EGR not seated, this issue it's only if i put my TPS at .9 to .3 volt.
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
May 24, 2013
#4
  • May 24, 2013
  • #4
stock TPS shouldnt be able to be adjusted. if its out of range its bad. do you have an aftermarket sensor? if so swap it back to a stocker and see if that helps.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,260
17,944
224
Massachusetts
May 24, 2013
#5
  • May 24, 2013
  • #5
http://www.stangnet.com/mustang-forums/threads/adjusting-your-tps-to-0-98v-is-not-necessary.825424/

There is no need to reset a TPS.


As for the issue with the TB, you probably need to perform the idle reset procedure now. It's usually necessary any time you adjust the idle stop screw. Basically unplug the IAC and open up the idle set screw a few turns to way open. Start the engine, and begin backing down the idle stop screw until barely over sustaining the engine in a low idle. At this point, shut the car off, unplug the battery for 30 mins and plug the IAC back in. Start the car and let it relearn idle.

Adjusting the idle stop screw will screw up your TPS adjustment, but thats fine because read the thread i linked earlier. No TPS code..you're fine
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 24, 2013
#6
  • May 24, 2013
  • #6
You guys with idle problems could save a lot of time chasing your tails if you would go through the Surging Idle Checklist. Over 50 different people contributed information to it. The first two posts have all the fixes, and steps through the how to find and fix you idle problems without spending a lot of time and money. I continue to update it as more people post fixes or ask questions. You can post questions to that sticky and have your name and idle problem recognized. The guys with original problems and fixes get their posts added to the main fix. :

It's free, I don't get anything for the use of it except knowing I helped a fellow Mustang enthusiast with his car. At last check, it had more than 125,000 hits, which indicates it does help fix idle problems quickly and inexpensively.

The setting the base idle and IAC cleaning procedures are in there as well.
 
You must log in or register to reply here.

Similar threads

Engine Hiccup at full throttle
  • keel
  • Jun 2, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
31
Views
606
Fox 5.0 Mustang Tech Today at 8:50 AM
keel
7
Engine Random hanging idle
  • 706 Saleen
  • Feb 11, 2026
  • Fox 5.0 Mustang Tech
Replies
9
Views
648
Fox 5.0 Mustang Tech Feb 19, 2026
86HO5.0
8
D
Engine Throttle sticky even after cable replacement
  • dqureshi06
  • Aug 16, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
354
Fox 5.0 Mustang Tech Aug 17, 2025
AeroCoupe
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
716
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
H
Forced Induction On3 Turbo Kit- Parts list NEEDED - 302 Stock Motor
  • Hirothecool1
  • Feb 27, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
1K
Fox 5.0 Mustang Tech Mar 7, 2026
slow84lx
S
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?