To Say It Rides Like A Brick Is.......

FoxMustangLvr · Nov 9, 2015

............an understatement.

I was thinking about transferring over my eibach pro kit front suspension from my notch to my hatch but I'm really wanting a better ride than that so I want to go coil over. Right now my suspension is stock up front and we have some bumpy roads where I live and my car rides like crap. I have emailed back and forth with Jack Hidley and he says I can fit the COP-1 coil over kit with their Bilsteins up front with my 03' Cobra reps without wheel spacers. He is suggesting a 12" spring with 175lb rate for superior ride comfort being priority #1.

Is this kit a big enough improvement over Eibach pro's with decent struts to justify a $825+ expense??
COP-1 kit is $375
Bilsteins are $225 each
So $825 total plus shipping....

Your thoughts and opinions please. This is just a full weight street driven car with the occasional romp on the skinny pedal.

hoopty5.0 · Nov 9, 2015

I love my coilovers. My coyote rides like a brick, fox rides like a continental. I do need struts though.

Boosted92LX · Nov 9, 2015

I don't have coilovers yet... I have eibach sportline with koni orange str.t shocks and i love my konis. MM makes a coilover kit for those konis in lieu of the bilstiens, and I'm glad... Because the konis are half the cost. I know bilstiens are good, but the konis don't suck!

Boosted92LX · Nov 9, 2015

hoopty5.0 said:
I love my coilovers. My coyote rides like a brick, fox rides like a continental. I do need struts though.

What shocks you got mang?

Edit: struts. Same ting

FoxMustangLvr · Nov 9, 2015

@hoopty5.0
You have the UPR K member and UPR coil over kit? What struts and spring?

Black1987 · Nov 9, 2015

My car use to be that way and then I switched to Strange 10 ways and never looked back. I can make super soft and hard as a brick. I run progressive springs in the rear and four cylinders up in the front.

hoopty5.0 · Nov 9, 2015

The struts are what came on the car, but I'm going to replace them soon. Junk. Also unsure of what spring. Lemme look and see if I can find it.

hoopty5.0 · Nov 9, 2015

14-150. This was on the '85, but the same K member and coilovers are on the '90 right now.

FoxMustangLvr · Nov 9, 2015

MM says theirs will fit my car but UPR says theirs won't (with my wheels). I wonder if MM have a smaller spring diameter?

hoopty5.0 · Nov 9, 2015

That would be difficult. The springs in my pics are Eibachs and hug the strut very closely.

stykthyn · Nov 9, 2015

I'm going with the koni sleeves for my coil overs. Im not knocking bilstiens as they have been great on every vehicle I've had them on I just don't like the idea of only being able to use bilstien struts.

GroverDill · Nov 9, 2015

I have the MM coilovers, it rides pretty nice. However I am not 100% sure if I would buy them today if I didn't already have them.

stykthyn · Nov 9, 2015

GroverDill said:
I have the MM coilovers, it rides pretty nice. However I am not 100% sure if I would buy them today if I didn't already have them.

What would you have done differently?

Chuckman · Nov 9, 2015

FoxMustangLvr said:
MM says theirs will fit my car but UPR says theirs won't (with my wheels). I wonder if MM have a smaller spring diameter?

mm usually does a shorter, higher-rate spring more suited to road racing. most of the others (teamz, upr, wolfe, racecraft etc) are usually setup for drag racing with a taller, lower-rate spring. those taller springs typically put the adjuster right in the middle of the sidewall, which can be a problem with a 9" or so wheel even with a too-small 245-wide tire. the shorter road-race springs will have the adjust end up a bit higher on the strut, giving a bit more room.

or at least so says the research i was doing a couple months ago.

stykthyn · Nov 9, 2015

View: https://youtu.be/4no20j9nuNc

This is what made me decide to go MM

A5literMan · Nov 9, 2015

I went with 150# mm coilovers with strange 10 ways. I have the struts set right in the middle and waaay better than the eibach pro kit it replaced. Money well spent IMO. Quality components and they make very little noise. I haven't turned them to full loose(drag) or tightened them down either. I had one hard braking incident and the front end barely dove down(slightly more than stock is my guess). Car handles worse if you plan on throwing it into turns with that soft of a spring but if I stiffened the struts I think it would be fine. (I don't get much entertainment out of the twisties)

mikestang63 · Nov 9, 2015

stykthyn said:
View: https://youtu.be/4no20j9nuNc

This is what made me decide to go MM

^this. that is why most guys buy MM and the ones that buy UPR end up wrapping their struts with tape to try and keep the knocking noise down. Do a google search and you will see this is a common problem with UPR coil overs. Buy the MM and do it right the first time.

84Ttop · Nov 9, 2015

A5literMan said:
I went with 150# mm coilovers with strange 10 ways. I have the struts set right in the middle and waaay better than the eibach pro kit it replaced. Money well spent IMO.

This is exactly the direction I would recommend, well played sir... well played!

FoxMustangLvr · Nov 10, 2015

A5literMan said:
I went with 150# mm coilovers with strange 10 ways. I have the struts set right in the middle and waaay better than the eibach pro kit it replaced. Money well spent IMO. Quality components and they make very little noise. I haven't turned them to full loose(drag) or tightened them down either. I had one hard braking incident and the front end barely dove down(slightly more than stock is my guess). Car handles worse if you plan on throwing it into turns with that soft of a spring but if I stiffened the struts I think it would be fine. (I don't get much entertainment out of the twisties)

I just did a search on the strange 10 ways and I hear the struts clunk a lot (or used to 2+ years ago).

Chuckman · Nov 10, 2015

The strange struts use a slightly smaller diameter shaft than others. Teamz caster/camber plates are made for them, i used mm plates and wrapped a .006" shim around the strut shaft when i installed them, takes up the slack and no clunks.

To Say It Rides Like A Brick Is.......

I love my Pimp

mechanicus terribilis

It's only an inch or two. What's the big deal?

It's only an inch or two. What's the big deal?

I love my Pimp

my wife Bedazzled my input shaft

mechanicus terribilis

mechanicus terribilis

I love my Pimp

mechanicus terribilis

I want to measure mine. It doesn't look that tall.

GoldMember

I want to measure mine. It doesn't look that tall.

GTFO you fat, heavy bastard

I want to measure mine. It doesn't look that tall.

At least it is lumpy...

They make new pistons every day, so why worry?

I love my Pimp

GTFO you fat, heavy bastard

Similar threads

Privacy & Transparency

Privacy & Transparency