• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Transmission Question & Check Engine Light

  • Thread starter Thread starter afast93stang
  • Start date Start date Jan 20, 2006

afast93stang

Founding Member
Jan 6, 2002
1,407
4
39
North Texas
Jan 20, 2006
#1
  • Jan 20, 2006
  • #1
This is a t-5 from an 89 GT, the 5.0 and mostly everything else was swapped into a 93 coupe by myself. The car runs great, all the lights work, etc... but im not able to pull codes and the check engine light is always on.


There is an extra connector that didnt have anything to hook up to when I put the 1993 engine harness on. The donor car is long gone. Everything else fell into place and connected correctly.

So the question is, what does this connector go to and is it the cause of me not being able to pull codes? 2 different garages couldnt pull the codes either (one dealing only in mustangs).


[Looking from the drivers side under the car looking upwards]
 
B

bcd

New Member
Jun 23, 2005
274
0
0
arab al
Jan 20, 2006
#2
  • Jan 20, 2006
  • #2
I think thats the nuetral gear switch (or something to that effect) and if it is i have heard that it will keep you from pulling codes. jrichker said something about it in a my comp wont throw codes thread the other day. no to be confused with my mycomp wont throw codes thread from the other day.
 
S

ss93cobra

Founding Member
Apr 10, 2002
1,422
1
0
Wilmington NC
Jan 20, 2006
#3
  • Jan 20, 2006
  • #3
looks like an O2 sensor plug in.
 
B

bcd

New Member
Jun 23, 2005
274
0
0
arab al
Jan 20, 2006
#4
  • Jan 20, 2006
  • #4
http://forums.stangnet.com/showthread.php?p=5853034#post5853034

jrichker and hissin50 put up some good stuff on here about comp not throwing codes
 

afast93stang

Founding Member
Jan 6, 2002
1,407
4
39
North Texas
Jan 20, 2006
#5
  • Jan 20, 2006
  • #5
So if I am reading the wiring diagram correctly in the other post, I have to tap in and connect pin 46 and 30 to the connectors and that should fix my problem?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 20, 2006
#6
  • Jan 20, 2006
  • #6
The neutral gear switch plugs into a connector on top of the T5.

On the attached drawing, it is the pigtail hanging off the top cover. Item #6 on the drawing.

 

Attachments

  • T5 external parts 85%.GIF
    74.3 KB · Views: 17,271

afast93stang

Founding Member
Jan 6, 2002
1,407
4
39
North Texas
Mar 10, 2006
#7
  • Mar 10, 2006
  • #7
So I finally had time this week to work on the stang, I wired the Neutral Saftey Switch to pins 30 and 46, since the wires ones coming off the NSS were both black I had to guess at it. I tried the wires both ways, nothing shorted out , the car started and ran fine, but I still have the check engine light and I still cant pull my codes. My car gets around 25mpg on the highway so I know things are running correct, I just want my check engine light to go off!
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 10, 2006
#8
  • Mar 10, 2006
  • #8
With the power off, measure the resistance between the computer test ground (black/white wire) on the self test connector and battery ground. You should see less than 1.5 ohms.



If that checks good, remove the passenger side kick panel and disconnect the computer connector. There is a 10 MM bolt that holds it in place. Measure the resistance between the STI computer self test connector (red/white wire) and pin 48 on the computer main connector.

Diagram courtesy of Tmoss & Stang&2birds



See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help on 88-95 wiring http://www.veryuseful.com/mustang/tech/engine

The following is a view from the computer side of the computer connector.
 

afast93stang

Founding Member
Jan 6, 2002
1,407
4
39
North Texas
Mar 10, 2006
#9
  • Mar 10, 2006
  • #9
I want to make sure im doing this right, use the black probe as a ground, and the red probe into the black/white wire and it should read less than 1.5.

If im doing this correctly then its reading higher than 1.5
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 10, 2006
#10
  • Mar 10, 2006
  • #10
afast93stang said:
I want to make sure im doing this right, use the black probe as a ground, and the red probe into the black/white wire and it should read less than 1.5.

If im doing this correctly then its reading higher than 1.5. What is my next step?
Click to expand...
You get to either replace some wires or chase through the harness to find the bad connections. In rare cases, the computer is a fault.Do not replace the computer until you have completely checked the wiring. The computers are very reliable and seldom fail.
 

afast93stang

Founding Member
Jan 6, 2002
1,407
4
39
North Texas
Mar 10, 2006
#11
  • Mar 10, 2006
  • #11
I regrounded the ground lead to the car body and was finally able to pull codes with a circuit tester. Dam that Code puller....
I pulled 2 codes, 22 and 67

22 is MAP (vacuum) or BARO signal out of range - MAP -Correct?

67 is Park/Neutral circuit fault - PNP Correct?
 
You must log in or register to reply here.

Similar threads

Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
393
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
A
Check Engine codes jumping around
  • azactor
  • Jan 9, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
3
Views
304
1996 - 2004 SN95 Mustang -General/Talk- Sep 24, 2026
DadLife0724
M
1996 GT Speedometer electrical nightmare
  • moon96gt
  • Oct 7, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
194
SN95 4.6L Mustang Tech Oct 17, 2026
CAMTWO1070
Electrical 88 EEC Injectors batch firing ?
  • Dustin 86GT
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
660
Fox 5.0 Mustang Tech Jan 8, 2026
gkomo
L
95 gt engine vibration
  • lenzgt
  • May 11, 2026
  • 1994 - 1995 Specific Tech
Replies
6
Views
382
1994 - 1995 Specific Tech May 26, 2026
lenzgt
L
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?