• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Vert hydraulic line setup

  • Thread starter Thread starter im2damncool
  • Start date Start date Dec 6, 2005
I

im2damncool

Founding Member
Dec 28, 1999
249
0
0
Chico, CA
Dec 6, 2005
#1
  • Dec 6, 2005
  • #1
I recently had to change the hydraulic lines that run the vert top. But I didn't pay attention the the routing order. ie: top line of right cylinder to vert motor to bottom line of left cylinder. Anybody know how they're supposed to be routed?
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Dec 6, 2005
#2
  • Dec 6, 2005
  • #2
Man that is a good question. I don't remember, I'll run out and check though...

Edit: I looked but it was either too dark or I was too cold. I can check again tomorrow afterwork but your probably right in the middle of the setup.
 
I

im2damncool

Founding Member
Dec 28, 1999
249
0
0
Chico, CA
Dec 9, 2005
#3
  • Dec 9, 2005
  • #3
Anything you can do would be very much appreciated. I have them hooked up now but I think the order's wrong cause it's fighting me if I try and pull the top up.
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Dec 9, 2005
#4
  • Dec 9, 2005
  • #4
Sorry man I forgot all about this thread... I can't really see a whole lot... It appeared that the lines in the front of the motor (fiting facing the hood) go to the bottom of both cylinders.

How are they set up on your car currently?
 
I

im2damncool

Founding Member
Dec 28, 1999
249
0
0
Chico, CA
Dec 17, 2005
#5
  • Dec 17, 2005
  • #5
Can anybody verify that? I don't want to hook it up wrong and blow a fitting when I try it.
 

Blakthorn

Member
Jul 24, 2004
299
1
16
US
Dec 17, 2005
#6
  • Dec 17, 2005
  • #6
did you fill up the vert fluid while you were in there?
 
I

im2damncool

Founding Member
Dec 28, 1999
249
0
0
Chico, CA
Dec 17, 2005
#7
  • Dec 17, 2005
  • #7
ya, fluid level's good. And I found a post that tells how to bleed the lines once they're hooked up right.
 
You must log in or register to reply here.

Similar threads

How to Route Subframe-Style Intermediate Brake Line?
  • cnorman31
  • Nov 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
0
Views
167
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 29, 2025
cnorman31
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
614
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
A
SN95 Hydroboost in a Fox | Brake lines
  • arc_jpiv
  • Sep 4, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
458
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 14, 2026
2000xp8
R
Microsquirt tune for stroked 351W in a foxbody
  • roldy
  • Jul 26, 2026
  • Digital Self-tuning Forum
Replies
7
Views
419
Digital Self-tuning Forum Oct 25, 2026
roldy
R
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
1K
1996 - 2004 SN95 Mustang -General/Talk- Oct 7, 2026
2v_johnny
2
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?