• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Went to the track tonight

  • Thread starter Thread starter Rootus
  • Start date Start date Aug 29, 2004

Rootus

Officially Addicted
Feb 8, 2003
6,659
1
0
Portland, Oregon
Aug 29, 2004
#1
  • Aug 29, 2004
  • #1
Man our local track sucks. Not many fast cars to lay down good rubber, no VHT preparation, and a whole gaggle of ricer kiddies who track water all the way to the starting line.

But I did get a new personal best. Here are the complete timeslip details for my last run of the evening. Even with it 65* outside, I was still getting a lot of pinging in fourth gear. Grrrr....

R/T 0.085
60' 2.108
330 5.742
1/8 8.685 @ 84.34
1000 11.214
1/4 13.341 @ 106.14

I think I will probably not go back again this year. I couldn't use full throttle until I was firmly into 2nd gear (and I still kept blowing off the tires going into 2nd). And my T-5 hates me. It was grinding a bit going into 3rd (only when I try to put it into 3rd at 6000 RPM ). And on the way home it was doing what it usually does after I abuse it at the track -- grind grind growl growl, funny sounds coming from it. Not quite sure what is making all the weird sounds, but it usually goes away after about a day .

So in the Spring, I plan traction. And a TKO, because I don't think the T-5 is going to take many 5000 RPM clutch dumps...

Dave
 

Grn92LX

Fidanza Man!
Founding Member
Jan 14, 2001
6,819
64
129
New York
Aug 29, 2004
#2
  • Aug 29, 2004
  • #2
If you look on your dyno graph, it goes lean up stairs. Thats the cause of your pinging most likely. That trap speed doesnt corrolate with your dyno numbers but you had some issues. Are you using any kind of tuning device? If not, i'd suggest adding some fuel pressure and hopefully the eec wont adapt those changes out. I'd say 3-5psi will be good. A set of drag radials are perfect for you. I used to cut 1.8's all day with them.
 

Rootus

Officially Addicted
Feb 8, 2003
6,659
1
0
Portland, Oregon
Aug 29, 2004
#3
  • Aug 29, 2004
  • #3
I have a tweecer, so I can make adjustments to the higher end. I did add back about half a point of A/F on all of the high load values (any RPM) from what I had it set to on the dyno. I think it might help a little also if I can get my filter into the fender -- after idling for a bit to get up to the line, it's sucking in air at over 100* from the engine bay. It cools off a little going down the track, but not fast enough.

Dave
 

95snoozer

Active Member
Dec 14, 2002
2,572
1
48
RCR
Aug 29, 2004
#4
  • Aug 29, 2004
  • #4
nice.... definitely get that filter in the fender. it helped me a bunch.

your tiems are right around mine last night. 13.12 at 106.33
 

final5-0

Mustang Master
Apr 6, 2003
6,817
12
79
DFW Texas
Aug 29, 2004
#5
  • Aug 29, 2004
  • #5
Hey Dave

You'll be in the 12's with no probs when you get those pesky little details sorted out.

Very frustrating to know how close you are to your track goal when little things like you mention seem to thumb their nose at you.

I've wanted to get back to the dyno and make a few runs down the strip myself.

Later
Grady
 

Rootus

Officially Addicted
Feb 8, 2003
6,659
1
0
Portland, Oregon
Aug 29, 2004
#6
  • Aug 29, 2004
  • #6
I am actually happy with last night's results. I consistently saw two to three mph faster than before, which is good. The rest is driver .

How about this -- I will just blame it on the track, instead of the fact that last night was the first time I've been to the track this year . My last run of the evening was against a 2003 Cobra with a 2.75 pulley -- he only got a 12.929 @ 107.44.

Dave
 

duner

Mr. Warmth
Jul 21, 2003
1,756
3
0
Oregon
Aug 30, 2004
#7
  • Aug 30, 2004
  • #7
HairyCanary said:
Man our local track sucks. Not many fast cars to lay down good rubber, no VHT preparation, and a whole gaggle of ricer kiddies who track water all the way to the starting line.
Dave
Click to expand...

Not to mention the track workers spreading water outside of the box. Seemed like every jackass/****tard was using the water box.

I think the funniest thing I saw all night was a ricer Honda with the rear tires in the box. With his e-brake firmly engaged and one front tire spinning he dragged his motionless rear tires halfway to the start line. Looked like a dog crawling after a bone with two gimp legs
 

95snoozer

Active Member
Dec 14, 2002
2,572
1
48
RCR
Aug 31, 2004
#8
  • Aug 31, 2004
  • #8
wtf... i tried to start a new thread and it posted here
 

zenboy99

Founding Member
May 12, 2002
2,212
0
47
Madison, WI
Aug 31, 2004
#9
  • Aug 31, 2004
  • #9
Congrats on the new times. Patience grasshopper.
 

Joes95GT

New Member
Jan 23, 2003
3,132
1
0
Delaware
Aug 31, 2004
#10
  • Aug 31, 2004
  • #10
Ignore the pinging. That's an excuse for a new motor.

They say 2-tenths for every 1-tenth in the 60'. Get it down to 1.8 and you are solidly into the 12's. The car's running great, and it's evident by the times.

Good R/T, too.

Joe
 

Rootus

Officially Addicted
Feb 8, 2003
6,659
1
0
Portland, Oregon
Aug 31, 2004
#11
  • Aug 31, 2004
  • #11
duner said:
Not to mention the track workers spreading water outside of the box. Seemed like every jackass/****tard was using the water box.
Click to expand...
That was definitely irritating. I tried to squeeze by as close to the guardrail as possible, but I still ended up running the passenger side tires through the puddle. I wish the workers would have tried harder to keep the water contained.

I think the funniest thing I saw all night was a ricer Honda with the rear tires in the box. With his e-brake firmly engaged and one front tire spinning he dragged his motionless rear tires halfway to the start line. Looked like a dog crawling after a bone with two gimp legs
Click to expand...
I didn't see that, if I had I think I'd still be laughing now...

95snoozer said:
wtf... i tried to start a new thread and it posted here
Click to expand...
What, you don't like it in my thread?

Joes95GT said:
Ignore the pinging. That's an excuse for a new motor.
Click to expand...
Thankfully 5.0 shortblocks are cheap! Yesterday on the way home I saw a puff of some kind of smoke or steam coming from in front of the car, on the drivers side. No idea what it was, I couldn't figure it out. Just to be sure, I did check this morning to make sure the radiator is under *normal* pressure .

Dave
 

95snoozer

Active Member
Dec 14, 2002
2,572
1
48
RCR
Aug 31, 2004
#12
  • Aug 31, 2004
  • #12
HairyCanary said:
What, you don't like it in my thread?

Dave
Click to expand...


 
You must log in or register to reply here.

Similar threads

S
Engine Stalls when downshifting/coasting
  • Scott_S
  • Nov 5, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
698
Fox 5.0 Mustang Tech Nov 6, 2025
Mustang5L5
K
TKX Transmission Shifting Problem
  • KWC156
  • Jun 23, 2025
  • Other Auto Tech
  • 2
Replies
21
Views
2K
Other Auto Tech Jun 13, 2026
427nostang
4
X
VE Table Not Dialed? Send Me Your Datalog.
  • X-cam34
  • Feb 8, 2026
  • Digital Self-tuning Forum
  • 2 3
Replies
49
Views
1K
Digital Self-tuning Forum May 1, 2026
X-cam34
X
B
Questions About T5 Manual
  • Blackout67
  • Apr 13, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
10
Views
593
1996 - 2004 SN95 Mustang -General/Talk- Apr 22, 2025
89ripper
Which one of these 3 intakes make the most sense for my 331 combo
  • from6to8
  • Jul 25, 2024
  • 1994 - 1995 Specific Tech
Replies
7
Views
2K
1994 - 1995 Specific Tech Jul 26, 2024
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?