What did your Fox run stock?

Flossy · Jan 15, 2012

I couldn't find a thread of stock fox 1/4 times... Looking for stock times... port work is okay, but preferably with no visual changes. Port work and exhaust is okay! No aftermarket heads, intake, or cam and such.

My goal is keep my car looking bone stock. I will be doing a t-5 swap and will be aiming for 13.9 stock, then from there I will do gears, maf, and port work and such.

Post your:
60 ft, 1/4 time, and trap speed.
Please list your Year, model, trans, and mods!

I really enjoy reading what people do with stock mustangs.

ReefBlueHatch · Jan 15, 2012

I only went to the track once in my life, but here's what I did, 14.4 at 95 mph with I think was 2.2-2.4 60ft time. This was on street tires with no trac-loc and a really unbalanced driveshaft.

'93 stock from oil pan to throttle body with 73k
5 speed with 3.73 gears
CAI (no gains with this)
C&l 76mm MAF
Stock headers with O/R H-pipe and Flomasters
Timing @ 16 degrees

Ozz · Jan 15, 2012

It ran perfectly without ever having any problems

hoopty5.0 · Jan 15, 2012

14.7 with a 2.1 60' on street tires and a busted arse T-5

Jason 302 · Jan 15, 2012

60'............1.80
330...........5.43
1/8............8.50
MPH.........79.77
1000.........11.16
1/4............13.41
MPH.........100.08

Mods: no passenger seat, no front sway bar, no spare tire, cheater slicks, 3.73 gears, K&N filter, "short belt", U/D pulleys, electric fan, full exhaust.

aar0s · Jan 15, 2012

my vert would have been doing good to run a 15 flat!

LarsD · Jan 15, 2012

Mine full weight with a CAI, O/R H pipe, blowmaster cat back, and 3.55's ran a best of 14.79 with an awful 2.2X 60' (not 100% sure on the 60' but I know it has never been better then 2.2). This was with my very tired stock 150K+ mile long block.

TwoToneHatch · Jan 16, 2012

When my '89 GT was still AOD and dead stock besides a dynomax catback , cheap shift kit and 3:73's I went 14.7 on a 95 degree day and in the late fall I went 14.2 @ 96 after letting the car sit for a couple hours and took air out of the rear tires .

85_SS_302_Coupe · Jan 16, 2012

Well, i got mine with 3.73 gears and a C4, offroad H and Flows, but it was otherwise 100% stock engine wise and it ran 14.5s on street tires. That's as close to stock as i've ever owned it.

VibrantRedGT · Jan 16, 2012

I'll do one a little different for comparison sake. Mine was a 1994GT and pretty much took it to the track after I installed every part.

From 1994 to 2003:
Day 1, bone Stock 15.9 at 90MPH on the stock Firestones, because I had never been down the track before.
Got that down to 14.5 at 94MPH on the stock Firestones after I learned how to drive it.
A few weeks later with only K&N and 3:55 gears on the stock Firestones, 14.3 at 95MPH.
Added MT Slicks, 14.09 at 94MPH. After a bunch of launches the stock clutch went South.
New Cobra Clutch, Equal Length Headers, MAC h-pipe (no Cats), Flowmaster kit, 14 degrees of timing and K&N, 14.2 at 97MPH all day.
Added Edelbrock Performer Intake, 70MM Throttle Body, Pro-M 77MAF with street tires, 13.62 at 100MPH.
Added GT40X heads, Crower Cam, 24lb Injectors on street tires 13.19 at 106MPH. With slicks 12.60's possible.
Added Vortech S-Trim V-1 Supercharger at 12psi, 42lb injectors, Powerpipe on street tires 12.4 at 120MPH spinning for most of the run. With traction 11.80's easily.

Rick 91GT · Jan 16, 2012

Ozz said:
It ran perfectly without ever having any problems

Man if that ain't the truth..lol

I had aftermarket shocks, struts, full exh, 3:73 gears, 1.7 rockers, ram air, under drives, no front sway, control arms, shor belt, fiberglass hood and some weight reduction 12.89 @ 104mph on a set of DOT legal M&H Racemasters (basically a ET STREET) all on Weld big and littles.

Launched at 5000rpm and drive it like I stole it. Stock 169,000 mile motor.

Ill never forget my first pass down the 1/4 mile 17.3, 2.8 60ft on street tires, I guess I should have left on green..lol

MFE92 · Jan 16, 2012

They all ran 13's bone stock paper filter, duh

srtthis · Jan 16, 2012

stock foxbody? no such thing... all sport flowmaster and welds

79'293stang · Jan 16, 2012

14.5 @ 98mph, 1.9 60'. K&N filter, Flowmasters, on street tires with a slipping clutch. Not to bad for a mostly stock 4 popper

5LiterWes · Jan 17, 2012

14.3 @ 96. 3.73's and full exhaust(Ford Racing shorties, OR-H, Flows). Stock 170K mile longblock.

Hoping for 105+ on the boost.

srtthis · Jan 17, 2012

5LiterWes said:
14.3 @ 96. 3.73's and full exhaust(Ford Racing shorties, OR-H, Flows). Stock 170K mile longblock.

Hoping for 105+ on the boost.

serious? i went 107 NA with E7's and a Bcam. id want to be closer to 115 with a blower

5LiterWes · Jan 17, 2012

This is 5lbs of boost on a tired stock motor in a full weight GT in street trim.

Congrats on 107... you must have been close to 300rwhp or had a very light car.

srtthis · Jan 17, 2012

no where near 300hp and its lightish but i still have a lot of left i can take out of it.

Mustang5L5 · Jan 17, 2012

14.8 @93mph bone stock AOD with 2.73s

rbonella · Jan 18, 2012

14.1 @ 101 with:
full exhaust with shorties/ h pipe/ flows/ no cats
2:73s
bcam
pullies
old school hoosier quick times
I miss that car cause it was my first

What did your Fox run stock?

Flossy

Member

ReefBlueHatch

Active Member

Ozz

I think I have a problem here.

hoopty5.0

mechanicus terribilis

Jason 302

aar0s

LarsD

TwoToneHatch

Active Member

85_SS_302_Coupe

it sucks (I know) to be on the receiving end

VibrantRedGT

"STANGNET'S PENGUIN SMACKER"

Rick 91GT

Mustang Master

MFE92

srtthis

the guy doing it does every local racers rear end

79'293stang

Active Member

5LiterWes

Member

srtthis

the guy doing it does every local racers rear end

5LiterWes

Member

srtthis

the guy doing it does every local racers rear end

Mustang5L5

That is…until I whipped out my Bissell

rbonella

Member

Similar threads

What did your Fox run stock?

Member

Active Member

I think I have a problem here.

mechanicus terribilis

Active Member

it sucks (I know) to be on the receiving end

"STANGNET'S PENGUIN SMACKER"

Mustang Master

the guy doing it does every local racers rear end

Active Member

Member

the guy doing it does every local racers rear end

Member

the guy doing it does every local racers rear end

That is…until I whipped out my Bissell

Member

Similar threads

Privacy & Transparency

Privacy & Transparency