Who's polished a trueflow pipe...and...

DMAN302 · Nov 2, 2006

I have aquired a trueflow C&L inlet pipe from one of stangnets finer members and will be installing it after I've completed polishing it. Question is who has attempted to polish a trueflow?...casting looks rough, but I imagine it can be done reasonably well. Second question is...who is running this pc with at pro-m 75 bullet MAF and stockbox? If you are, did you have any clearance issues?
Tanx.
D

Deleted member 87397 · Nov 2, 2006

DMAN you are far too kind. Package is on it's way. The casting is rough, but there's plenty of material to work with. I'll PM you the tracking number.

Strype · Nov 2, 2006

DMAN302 said:
I have aquired a trueflow C&L inlet pipe

I want one

DMAN302 · Nov 2, 2006

fastfox86 said:
DMAN you are far too kind. Package is on it's way. The casting is rough, but there's plenty of material to work with. I'll PM you the tracking number.

You have been too helpful...seriously,thanks!!!!

Strype...you should...I think you should.

grey5.0beast · Nov 2, 2006

he's being a great help to me too

I love you fast fox

and No I have no idea how to polish anything lol

DMAN302 · Nov 2, 2006

no he's my new friend....

MyBad70 · Nov 2, 2006

Strype said:
I polish "pipes" all the time

not the best, but he does have mad skills

Strype · Nov 2, 2006

MyBad70 said:
not the best, but he does have mad skills

I hope your K&N fills with water again

DMAN302 · Nov 2, 2006

grey5.0beast said:
he's being a great help to me too

I love you fast fox

and No I have no idea how to polish anything but my binkie lol

Fixored.

MyBad70 · Nov 2, 2006

lol...stop by when u get off work.....

DMAN302 · Nov 2, 2006

Can't I have to cook dinner.

MyBad70 · Nov 2, 2006

damn. ok. what time will it be done?

Strype · Nov 2, 2006

beast polishes his binkie!!! beast polishes his binkie!!!

Ozz · Nov 2, 2006

Despite being really rough and bumpy you still have plenty (as stated) of material to work with. Basically, sand it down. A lot. A flap wheel will come in real handy but you've got to be careful on how gritty you go and how much metal it takes off. If you get haphazard with it you'll end up with it being unsmooth (although still a lot better than it is now with all the bumps and graininess).

Once that's done you can break out the sandpaper or a DA sander and use something in a 220-280 grit (usually what I use when I have to follow up a flap wheel job) and smooth it all out nicely. Then proceed as usual

And as always - hurry up so you can post pics

DMAN302 · Nov 2, 2006

I will, I will...as you did Dave I found a local plating company.They will take on the project if I find the material won't provide a decent result...as you know some castings just don't like to play nice, but I'll do my best. I will have pics as soon as I get the chance . Really would prefer to have gone with a custom CAI for looks, but my tune is with the stockbox in place...so I just have to make the best of it.

Ozz · Nov 2, 2006

Cool. However, my Powerpipe problem with that was the pipe was, at least according to the chrome shop, "aluminized steel". I didn't ask much else but I'd guess it was steel with some kind of coating of aluminum on top or mixed in...or something. But that explains why it didn't play nice. I must have had it half-bare to steel and half-with aluminum still showing, because some parts would polish up nicely and others I could not get shiny to save my life.

I believe the C&L pipes are all aluminum. If they're like the SN95 ones, they are. I did one for a friend over spring and it came out real fine.

DMAN302 · Nov 2, 2006

Thanks buddy..supplies and patience are ready and able.

Strype · Nov 2, 2006

mansonozz said:
Despite being really rough and bumpy you still have plenty (as stated) of material to work with. - hurry up so you can post pics

You're sick!!!

MyBad70 · Nov 2, 2006

Strype said:
You're my hero!!!

fixed

Deleted member 87397 · Nov 2, 2006

Well I do what I can. Now if only the ladies were fighting over me like DMAN and Beast right now I'd be set.

Who's polished a trueflow pipe...and...

DMAN302

My mom says thanks for the pearl necklace.

Deleted member 87397

Strype

Cuthbert catcher

DMAN302

My mom says thanks for the pearl necklace.

grey5.0beast

Cookies should never be DUNKED!!!

DMAN302

My mom says thanks for the pearl necklace.

MyBad70

Where's my Member?

Strype

Cuthbert catcher

DMAN302

My mom says thanks for the pearl necklace.

MyBad70

Where's my Member?

DMAN302

My mom says thanks for the pearl necklace.

MyBad70

Where's my Member?

Strype

Cuthbert catcher

Ozz

I think I have a problem here.

DMAN302

My mom says thanks for the pearl necklace.

Ozz

I think I have a problem here.

DMAN302

My mom says thanks for the pearl necklace.

Strype

Cuthbert catcher

MyBad70

Where's my Member?

Deleted member 87397

Similar threads

Who's polished a trueflow pipe...and...

My mom says thanks for the pearl necklace.

Deleted member 87397

Cuthbert catcher

My mom says thanks for the pearl necklace.

Cookies should never be DUNKED!!!

My mom says thanks for the pearl necklace.

Where's my Member?

Cuthbert catcher

My mom says thanks for the pearl necklace.

Where's my Member?

My mom says thanks for the pearl necklace.

Where's my Member?

Cuthbert catcher

I think I have a problem here.

My mom says thanks for the pearl necklace.

I think I have a problem here.

My mom says thanks for the pearl necklace.

Cuthbert catcher

Where's my Member?

Deleted member 87397

Similar threads

Privacy & Transparency

Privacy & Transparency