Search results

  1. T

    F/S 1990 Mustang GT Convertible

    Bright Red w/ Black Leather Interior and Black Top, 5 Speed Manual, Ford Racing 10.5” King Cobra Clutch, Steeda Tri-Ax Shifter, Mechanical Oil Pressure Gauge, Mechanical Water Temp Gauge, MAC 1 5/8” Equal Length Shorty Headers, MAC High Flow 2 ½” Catalytic H-Pipe, MAC 2 ½” Cat-Back, Ford 3.73...
  2. T

    EFI debut & other questions????

    Was 1987 the debut year for EFI on the 2.3? What was the last year the 2.3 had a mechanical fuel pump? When did the dual plug head show up? 1991?
  3. T

    Edelbrock 4.6 SOHC Intakes - 2 of them

    Two of them mentioned in the new April '06 5.0 Mustangs & Super Fords, p.70. They say there is a 4.6 SOHC EFI intake and a 4.6 SOHC carb intake as well as an ignition controller for the carb version. Anyone have ANY information? I looked for pics and I tried searching here. No dice. I also...
  4. T

    How to ID Speedo Drive Gear??

    I know that the speedo gears are color coded. Are the drive gears inside the transmissions color coded too? What color are the 7 and 8 tooth drive gears?
  5. T

    7 or 8 Tooth Speedo Drive Gear??

    Did some '96-'98 T45's in Cobra's come with 7 tooth drive gears instead of the normal 8 tooth drive gear? If all other factors are the same, how much would a speedo differ if a tranny had a 7 tooth from an 8 tooth gear? I put a '96 Cobra tranny in my '98 GTand my car is showing 1 mile on the...
  6. T

    Slow oil leak by a tensioner pulley?

    I noticed oil was slung around the path of my engine's serpentine belt. I looked around and found that there is a slow oil leak by what looks like a tensioner pulley/assembly on the middle/lower left of the front of the engine. I've heard this may have been a common problem at one point...
  7. T

    Tune Up Parts?

    I want to start gathering parts for a Spring tune up. What do I need. I have a 1998 4.6 2V GT. So far all I can think of is..... Spark Plug Wires Spark Plugs Fuel Filter Air Cleaner Filter What all does the 4.6 need? 5.0 I'm good on. 4.6 I'm not sure.... :shrug:
  8. T

    Any Upstate NY Emissions Inspectors Here?

    Any Upstate NY emissions inspectors on here? I have a question? About the visual portion of an inspection for a OBDII car (96+). What is the visual requirement for catalytic convertors? My '98, stock, has liek 4 convertors and 2 pre heaters. I'd like to put a catted Magnaflow X-pipe on...
  9. T

    327/331 Question - Clearencing Needed?

    Easy question for soemone who knows......does a 3.25" stroke crank and rod combo clear the bottoms of the 302's bores or does it need to be clearenced like the 3.40" stroke setups do?
  10. T

    4.6L Build Up Questions...

    I am curious about what realisticly could be expected from a dedicated naturally aspirated 4.6 build up in regards to power. I read an article once where they got around 400 hp at the crank. I thought that was pretty good for a 4.6L 281 inch engine. It's 1.42 hp per cubic inch, about 87 hp...
  11. T

    Cheap low buck N/A 2.3??

    How much power could I expect from an inexpensive 2.3 set up as the following.... 2.3 engine from whatever Lightly ported & decked cylinder head flat top pistons for about 10:1 compression Offy intake 350cfm carb Ranger spec camshaft MSD ignition system Backed by a full manual shift...
  12. T

    Buzzzzzzzing..............shift knob?

    I've had this annoying buzzing sound coming from my UPR shifter for about 2 months. It goes away about 90% if you hold the shift knob tight. Last night while I was driving I spun the knob off the shifter completely and the buzz was totally gone. It a FRPP leather Cobra knob. So the easy fix...
  13. T

    C3/C4 Automatic interchangeability question

    Does anyone know if the C3 3 speed auto that was put in early Rangers, Pintos and Mustang II's has interchangeability with the C4? I am trying to determine if the 2.3 to C3 bellhousing fits the C4 transmission. In the picture below from the Ranger Stration ( www.therangerstation.com ) it...
  14. T

    2.3 + C4 Automatic?

    I think the 2.0 in the mid-late 70's had a C4 automatic and the proper bell for the tranny pattern. But I'm trying to ascertain if this is possible and if so what parts are needed and what vehicles are out there that I can look to in order to find any parts I need. I have an idea for a...
  15. T

    All Aluminum PI Style 4.6 Intake - 5.4 Version coming Soon!!!

    Promising. http://www.hiperformancesolutions.com/index.html
  16. T

    13 or 14:1 possible with off the shelf parts?

    I don't know much about the 2.3 OHC other than they are tough as nails. But I am looking at these plentiful engines for a power sourch for a project to have a remote electrical power system. An off the grid kind of base camp if you will. But it would be powered not by traditional gasoline...
  17. T

    GT take off exhaust on the V6...

    Are there any sound clips of the GT take off exhaust on the V6? What does it sound like?
  18. T

    Anyone running 3.73's with stickshift?

    I'm curious how it is to drive. My next car (current is a '98GT) will most likely be either a V6 S197 or a '99-'04 GT. I only drive manual transmission cars.
  19. T

    Factory Camshaft Theory

    Don't know if anyone can confirm or dispell this theory I have. Ford is notrious about mixign and matching parts. For example, almost all 2V modular engines from about mid 99-current use the exact same cylinder heads and the exact same camshafts. If it's in a truck or a car or a Mustang...
  20. T

    Ford Gt Is In!!!

    :banana: :banana: Just got word that the Ford GT my Fathers Ford dealership was awarded is in. Gonna go see it tonight and try to take some pics. He got it in red with every single option you could get. F'N SWEET!!! :banana: :banana: I know this isn't tech, but the hardcore guys are in...
Top Bottom
Back
Forums
Menu