1994

Recently the clutch fork cover on my 1994 GT fell off. I cant find a replacement for the life of me. Online I can only find 96 and up and 93 and below. Any ideas where I can find a new one?

I have a pair of refurbished 1994-95 Ford Mustang spindle and hub assemblies(Left & Right). They start as a OEM FORD spindle core and they have been completely diassembled, cleaned, examined for wear and breakage, sand blasted, and powder coated in black. Then brand new OEM quality hubs are...

Ok, so I figured out the 5.0 runs off vacuum for the heat and ac, at first I was only getting ac and heat through the defrost vents, now that I fixed that tiny plastic line and plugged it back into the rubber AC vacuum line coming from the tree I’m only getting HIGH as a option. I have no low...

Does anyone have the Pinouts for the Microsquirt to 94-95 SN95 EEC Harness? It would greatly help me figure out how they are interfacing and working with/around the CCRM. (Specifically the AC WOT Cut and AC Control Circuit)

Anyone running an electronic fuel pressure sensor with your megasquirt. I'm looking to add on on my 95. What is your setup?

Asking $7000 firm. Florida car with no rust and in great condition ready to drive anywhere. Installed Parts: Air Intake BBK 8010 Mass Air Meter 76mm Ford CX1842 IAC valve OE AIT sensor Professional Products 70mm throttle body SR performance intake Speed demon heat reflective gold tape...

Note: I have wrote this post 3 times already and everytime I save it for some reason parts of the post go missing. Sorry if it doesn't make sense at the moment. A couple days ago I got a free 1994 Mustang V6 Convertible off Craigslist. It was an old filipino man who's build race cars (for the...

So i recently got ahold of a 94 gt 5.0 ho 5speed everything 100% on it but two days ago i was drivong home and the oil pressure gauge and coolant temp gauge just pegged out but it wasnt running hot and then i cut it off and it killed the battery. So i need help asap ita my daily and i got a...

hey guys, so at the moment I have the factory 302 with 80,000 miles on the mustang. love the car but its to slow. So after this deployment I want to throw a a stroked 351w to 408 CID. looking for someone who's done the same thing as me and what they recommend. heres what I want: 1. Keeping the...

hey guys been a while. so ill start from the beginning. a few months ago I got beat by an SRT4 while i was in my 1994 ford mustang gt. I know. since then I came to the realization that I need a faster motor not car. ive been running back and fourth on ideas still haven't picked a route yet...

Hi guys and gals. I am a few months into owning this 1994 Mustang Gt Convertible 5spd with 87K on the clock and I'm having nothing but issues. I'll give the backstory and then the current issue. When I first bought the car back in April I believe, I did an ignition system tune-up. Dizzy cap and...

Not sure if this is the forum for this but a while ago I purchased some Axial Projector Headlights form american muscle.Link right here: http://www.americanmuscle.com/projector-headlight-led-black-9498.html I have been having an extreamly hard time getting them installed. Any tips if you guys...

I have a 1994 Mustang GT that we traded a 98 f150 for. The car needed some work and had a surging idle and miss. The idle used to surge from 600 to 1000 and ran like sh*t. Since then we have cleaned and replaced the IAC valve, checked the plugs, plug wires, coil, and MAF. We then went to the...

just wondering what some of you guys that have swapped the H/C/I what you swapped it for and what you got for specs on the dyno and rpm range

ive been looking around trying to find a decent cam with i good sound but not too aggressive and also gives me good performance. i have the 94 gt and was seeing a lot of people getting the E303 cam vs something from trick flow or comp cams. first id like to know why, secondly id like to know if...

anyone know if its possible to swap the cam in the sn95 1994-1995 mustang 5.0 302 without pulling the motor? thanks in advance

has ANYONE bought and put this -->Ford Performance Cylinder Heads M-6049-X307 cylinder head in a 1994 ford mustang non milled block and head from summit racing? if so what was your push rod length i know i should measure it but before i waste my time i was wondering if anyone has done this...

hey guys im new to the thread, hope to get to know some of you guys while im on here. so i have a 1994 ford mustang gt with the t5 world class 77,000 miles on it and its still mint condition. the other day while i was driving around and a dodge SRT 4 wanted to do a roll, so we did a couple and...

u

hello, I have a 1994 cobra, with a Bama tuner, off-road h-pipe, slp cat back, 65mm TB, and a cold air intake. I was wondering if I needed anything else to install a Ford E303 cam, would I need new heads or anything like that?