brake

So I finished the 5 lug brakes were locking up when I had cobras a friend gave me some sn95s for free and it was running perfect, today it started to lock up the fronts again, anyone has idea of what soft lines I can use it’s sn95 front and rear brakes to a 1984 ford mustang 5.0 I managed to...

So I’m almost done with my brakes Do I have to gut the proportioning valve? And can I run my brakes without one? Also I was pumping my brakes and no fluid is going down What could be the issue?

Hello, I'm new to the group. I have a 1990 LX Convertible white with red interior. I'm told it is an anniversary edition due to the badge on the dash and the factory 16" white wheels. I'm having brake issues, my power booster started leaking so I decided to change it. Looking at the master...

Bought an upgrade kit from CJ's to put Cobra front brakes on my GT. It came with Hawk pads, was on sale earlier this summer, but the rotors got backordered, so I am finally pulling it all out of the box and trying to assemble. I snapped the pads into the piston assembly, but the wear indicator...

Hey everyone. I have a 1985 notchback. Previous owner swapped brakes from a 1992 5.0 onto this and now I’m doing a 5 lug cobra conversion. I’ve done the fronts and then had to take the car to a shop for some work. By the time I get it back I don’t think I’ll have enough time to do the rears...

I am trying to change out my brake bleeder screw because I stripped the old one and I pull it out and I find this: It is completely bent??? The one one the right is the new one I got but unfortunately the wrong size… This isn’t normal, right? Why would this happen?

I am currently trying to gut my proportioning valve and install an adjustable one and after I have finally gotten off the leaking bolt I am faced with this. I assumed when gutting, the internals would just pull out but this is stuck. I have pulled as hard as I can but to no avail. Any suggestions?

Hello, The parking brake is not holding my 2.3l convertible in place. I took a look underneath while my friend engaged the parking brake, and found that the brake cables are not being pulled at all. (In the picture you can see cobwebs indicating it hasn't been moved in a while). Assuming there...

Hi everyone, I purchased a 2020 GT with now only 220 miles on it last week. I noticed starting the day after driving around for a bit an intermitteent yet consistent metallic scraping/rubbing noise that seems to be coming from the right passenger front tire area. I took the car back to the...

So it was brought to my attention that both brake lights aren't working. I unscrewed the taillight plugs from the tail lights and all the lights works, turn signals, reverse, warning & tail lights but the brake lights don't turn on. Both the small light and the bigger light that screw into the...

I just put an explorer 8.8 disc brake rear end that has had long side shortened. My problem is, the calipers are touching my leaf springs. No way it will work. I know a lot of people have done this swap. What did I do wrong? How do I fix this. Please, any ideas will be appreciated.

This is a 69 with rear drums and front discs. I've checked the fluid and topped it off and that had no effect. The brake pads were replaced a couple years ago (maybe 5k miles on them) and the master cylinder replaced as well so I'm thinking maybe it's the booster? Is there a good way to test...

I need some guidance on removing the lower nut securing the master cylinder to the hydroboost. I have searched online but found nothing. The space is so small and I can barely get a hand between the valvecover and master cylinder using the smallest socket wrench I have. I've also tried to go...

Listed is a Ford Mustang NEW Front Passenger/Right side ABS/speed sensor w/cable Ford Part # F7ZC-2C204-AA (Standard Brand) Asking $25/or make an offer, buyer pays shipping from Bradenton, FL (34210). Bought for a 1998 Mustang Cobra and was never used. Should fit most Mustangs from 1997...

I have a 2015 Mustang V6 convertible, out of warranty. The third brake light is not working. Tested light and it works, so no power to light. Any assistance on troubleshooting would be greatly appreciated. Thanks!

Listed is a Stainless Steel direct fit D.O.T. certified PTFE (Teflon) lined rear brake hose J&M part number 22515R and fits many V8 Fox and SN95 Mustangs. This fits over the rear axle and will reduce brake pedal "sponginess" and help brake responses. There are installation instructions posted...

Listed are New Front Hawk Performance HPS brake pads. Fits Brembo 4-piston caliper "Gran Turismo" 13" front brake kit*, 2000 Ford Mustang Cobra R, early(1992-2001) Dodge Vipers, and most(2000-2005) Ferrari 360s. Please do your research on fit for your specific application (I have included...

[SOLD] Posted is a Pair (1 driver's side, 1 passenger side), used 94-04 Mustang Cobra/Mach 1 rear brake calipers with slide mounts. These are located in Bradenton, FL (34210). Price reduced for Stangnet members only to $100/pair/obo SOLD SOLD SOLD This Cobra caliper is from a functioning 1998...

Hi, I'm new to the forum. I bought a 'garage find' '67 coupe 6 cyl w/ 4 lug drums all around . I want to keep it stock and need a hub for the front. I've searched many Mustang parts sites and only see hubs for 64-66. Anyone know where I can find a 4 lug hub for a '67? Thanks, BeeMoe

okay so long story short i was going to ask if its possible to fit a cobra booster (93) in to an 88 5.0 car, I've heard you have to beat the shock tower with a sledge in order to clear it in place. so i ordered the booster seeing if i was smarter then the average and if i could slip it in there...