camshaft

I'm currently rebuilding the bottom end of my 1990 302 fox that is carbd i'm having to because I got a knocking sound from the d.s, anyways i thought while the engine is out why not replace the cam while the engine is out because i know i am to lazy to ever want to pull the engine again down the...

I converted to a mass air a little bit ago, but to my knowledge the 8ld was a ho fire order ecu. My car only runs properly if I use a non ho spark plug set up. I've checked the ecu connector to the injector plug and everything lines up correctly. Always saw you need to swap wires around for...

Hello. Is there anyone here or someone that knows anyone that has run the Anderson N61 camshaft. Likes, dislikes, drivability. I haven’t seen much in forums about them. Really mostly just YouTube videos of them idling. Any info and opinions on them will be much appreciated Thanks!

This camshaft was removed from my 302 and I have been unable to find any information on it. Any help would be appreciated. I have called COMP and they were unable to tell me anything. Thanks in advance!!! Some of the numbers are the following 0019SS, 201824, 449358, 44-07-01

Hello all, Beginning my first time build of a 347 stroker in a 66 Coupe. I will be running the Eagle stroker kit with flat top pistons, 030 over bore. Have AFR 185 heads and plan to get an edelbrock air gap intake. I want to stick around 9.5:1 compression ratio to still be able to run pump gas...

I have a 2008 ford 4.6L mustang I bought recently. I got it off auction so I don't know anything about the vehicles mod history. From what I can tell, the owner put on Borla exhausts, cams, and a tune. The owner left his original SCT XCalibrator 2 tune installer with 2 tunes and 1 stock tune on...

Hello All, Recently, I rebuilt my 306 and topped it off with a set of tfs 11r 190's (56cc), and a lightly ported rpmii. I have a custom grind cam from ed curtis spec'd for another build of mine (ported gt40P's/explorer setup) .555/.558 224/220 @.050 111* LSA, and my question is should I be...

Hey guys i just extracted a cam from a 3.8 95 v6 mustang, did some measurements and got a TOTAL lift of .430. I dont have a way to measure Duration or LSA(although it is pretty tight), sorry. . Figured i would throw out that info. Someone is bound to find that handy when they decide to cam swap...

I have a 2004 3.9 V6 mustang. It had a sqeaking sound. I took it to the shop several times and replaced the belt, tensioner arm, water pump, ac compressor and alternator. The steady squeak is gone, but now it has a loud screeching sound that comes every 5-10 minutes. There is also a Service...

Howdy all. Looking to beef up my 67 289. I have 4bbl intake and carb, headers and duals. Any have experience with the summit cams? Loce to hear what guys have ran in thier 289s for street performance. Heres the one i am looking at... thoughts...

Hi I have a sn95 cobra i just got as my first car and am very interested in building it to a 347 down the road. I have experience in building engines just not anything serious mostly stock or small. Was wondering if someone could explain to me how to tell if a cam would work/fit in an engine...

i need to figure out what type of camshafts i have so that bama can make me a costum tune. I bought a 2007 mustang gt with long tube and camshafts, but i dont know what type of camshafts they are. I am alsp adding TB, CAI and intake manifold. I was told that the camshafts have engraving on...

I'm interested in installing Ford racing cams but looking for local help. I'm in the Jacksonville/Camp Lejeune, NC area. I have years of car know how but recently lost my garage. I have also never attempted a cam swap and know the timing can be tricky. Anyone nearby, who's done this, and is...

So for Christmas my parents told me they would by a custom camshaft for me to help me complete my 306. I would like to begin the process of getting this cam but I’m not sure how to get ahold of ed Curtis to give him all the details of my setup. I believe I found where to buy them but I’m not...

If interested, please contact me via email at 4rxq9-6346600331@sale.craigslist.org. I'm based in Phoenix, AZ. Ford V8 Cam Tool Kit 6498 by OTC. Includes: -525216 Camshaft Positioning Tool -525217 Camshaft Holding Tool -525218 Secondary Timing Chain Tensioner Tool -525219 Crankshaft Positioning...

I am building a 393w for my 1995 gt. '94 up 351w block. I am needing help with the camshaft, as i have everything else and i'm wanting to get the motor finished ASAP. 393w Scat rods and crank Mahle forged pistons Edelbrock performer rpm heads(ported) Edelbrock air gap intake (ported) Holley...

so first i have a 89 302 completely stock, i have gt40p heads, ford racing 1.6 roller rockers, chrome moly pushrods, .600 max lift valve springs from anderson, msd distributor, and an msd ignition system. im leaning between a cobra, explorer, or even an aftermarket intake manifold that wont...

I want to install the mutha thumpr cams in my 07 gt and was looking into cam degree. I was just told since my car has vvt it isn't really necessarily needed to be degreed. Is this correct?

I want to install the mutha thumpr cams in my 07 gt and was looking into cam degree. I was just told since my car has vvt it isn't really necessarily needed to be degreed. Is this correct?

ive been looking around trying to find a decent cam with i good sound but not too aggressive and also gives me good performance. i have the 94 gt and was seeing a lot of people getting the E303 cam vs something from trick flow or comp cams. first id like to know why, secondly id like to know if...