help needed

Hello, I work for a local garage in my area and am having some issues. A customer brought us a 1967 Mustang coupe with a T5 and a 303 from a foxbody. I put a clutch, pressure plate and flywheel in to match with the T5/302 combo. The car was kept with the original clutch linkages from the 67. He...

Hey everybody I’ve got a 2000 gt and I recently got a aftermarket midpipe and eshaust system installed but it’s knocking against the frame under the passenger side due to having hardly an inch of clearance. I can’t find anyone else having this issue so I’ve decided to make a post about it and...

Okay guys need some help here… I have a 1986 LX 5.0 that was converted from an AOD to a t5. All guages work however the cluster/hvac illumination only works when the car is put into reverse. Almost like it’s completing a ground at the switch. Coincidentally my reverse lights do not work at all...

Hi folks, I hope everyone is enjoying the summer. I've been having an intermittent issue with my car and I'm hoping someone can help me figure it out. Under normal driving conditions the car behaves as it should but after some spirited driving, mainly winding it out in the first 3 gears, it...

Hello, this is my first forum post but I'm having some problems with my 1989 Ford Mustang GT. About two weeks ago I had tried to start it up in the morning and it wouldn't start at all just crank and that's it. I had drove it the previous day and it started and drove fine, nothing out of the...

Hello all, I’m pretty new to the forum and this is my first post. I have a 2004 3.9 V6 and I swapped the upper intake manifold from a 4.2 onto it. I pretty clearly made a mistake, as my car now thinks it is at 18% throttle position (checked with live feed obd2 reader) when I’m completely off the...

Hey guys, I am new to the StangNet forums and I am helping a buddy work on his 1990 Mustang Foxbody 5.0. He purchased the car a couple of months ago and we have been working on this issue occasionally in the evenings. Heres the problem: The car starts and drives fine, with no idling issues...

Hey mustang owners, pretty new to this community. Recently got a 2003 gt manual and it’s a pretty decent car I have been plans for it from a engine swap all the way to the suspension but that takes time and money so one step at a time. i got the car when it had a spun bearing and 2 bent rods...

Hi everyone. I'm new to the Forums so I'm sure this question has been asked before but if you could help I would greatly appreciate it. I recently picked up a 91 foxbody with a built 347 stroker. It runs great but I feel I can get more out of it. I took it to the track on street tires and...

Found this in my new fox. I’m not sure exactly what it is. The hose comes from under the intake manifold and back behind the engine I believe. Maybe I’m missing something here but I’ve never seen this..

I have the BBK valve covers and the hydro booster seems to be in the way. It looks like a process to remove it...anyone found a way to remove the covers without getting to deep into it? If I remove the hydro booster can I get away with out disconnecting any lines at all? Picture is what I’m...

What up Fellow Stang Owners! Bought my SN95 a few months ago from my neighbor. May as well have stolen it from them for what I paid. Either way, the car was half dead and barely running. I've done a decent amount on it thus far (tune up, coolant flush, oil change, & rear drums and brake pads)...

Any help would be great. Bought a 1990 fox the motor had been swapped out of a 1995. All the 1990 top end and electrical was used. Car is not firing on 3 cylinder. Cylinder 2,4,and5 are not firing. New items are plugs,wires distributor, mas sensor,throttle sensor. Egr was deleted I have went...

Hey everyone, bought a 96 Cobra. Looking to purchase headlights identical to these and have been searching all over for them but cannot find them. Can someone please help? I'll attach and image. If anyone can tell me the name, provide a link, anything! I would greatly appreciate it. Thanks...

So I just finished rebuilding the TBI assembly on my 1985 Mustang 5.0 and the nut that screws into the back of the TBI assembly for the return fuel line has split in half. I cannot find replacement lines anywhere since it is the only year of TBI and I do not know what to do. It also seems that...

I have a newly built 347 i just installed into my 1993 mustang, new cam (b303), lots of other things thrown in as well, got everything in line, got it running for about 10 minutes, idling a little rough while it was cold which the old 5.0 i took out did as well so i figured maybe just an IAC...

I'm interested in installing Ford racing cams but looking for local help. I'm in the Jacksonville/Camp Lejeune, NC area. I have years of car know how but recently lost my garage. I have also never attempted a cam swap and know the timing can be tricky. Anyone nearby, who's done this, and is...