I have looked here on the forums and didn’t see anyone talking about a similar issue so if I missed it sorry but I am working on my dads ‘93 fox and I replaced the top cylinders and lines well I believe I have bleed it right I ran it up and down a few times 3-5 with the plug out and filled it up...
Have a 1993 5.0 with 14k miles car ran fine then one day it started take a long time to start it crank and can hear it pop like timing off then start die start die then start and stay running popped codes 21&24 drives ok kinda sluggish ran 96% of the gas out to make sure it wasn’t old gas...
I bought this car with all the go-fast parts installed by a shop from the previous owner in Pennsylvania. When I bought it, it ran great with no idle or other misfire or rough idle issues. I moved back home to California and needed the car to pass smog certifications. I had to do the...
I bought a used 95 V6 3.8, and i have done a lot of maintenance, last week, i was changing all the gaskets in the engine, was outside all day, in the night i was all tired and exhausted, i reassembled the engine, but connected the battery wrong, i noticed the alternator getting warm, and quickly...
So I swapped in my 01 cobra into a gt. I used the cobra engine harness and the cobra computer. So I’m using the ecu harness as well. The only things that were different I believe were the connectors for the ac line and radiator fan. So I spliced those and used the connectors from my gt harness...
Hello, I work for a local garage in my area and am having some issues. A customer brought us a 1967 Mustang coupe with a T5 and a 303 from a foxbody. I put a clutch, pressure plate and flywheel in to match with the T5/302 combo. The car was kept with the original clutch linkages from the 67. He...
Hey everybody I’ve got a 2000 gt and I recently got a aftermarket midpipe and eshaust system installed but it’s knocking against the frame under the passenger side due to having hardly an inch of clearance. I can’t find anyone else having this issue so I’ve decided to make a post about it and...
Okay guys need some help here… I have a 1986 LX 5.0 that was converted from an AOD to a t5. All guages work however the cluster/hvac illumination only works when the car is put into reverse. Almost like it’s completing a ground at the switch. Coincidentally my reverse lights do not work at all...
Hi folks,
I hope everyone is enjoying the summer. I've been having an intermittent issue with my car and I'm hoping someone can help me figure it out. Under normal driving conditions the car behaves as it should but after some spirited driving, mainly winding it out in the first 3 gears, it...
Hello, this is my first forum post but I'm having some problems with my 1989 Ford Mustang GT. About two weeks ago I had tried to start it up in the morning and it wouldn't start at all just crank and that's it. I had drove it the previous day and it started and drove fine, nothing out of the...
Hello all,
I’m pretty new to the forum and this is my first post. I have a 2004 3.9 V6 and I swapped the upper intake manifold from a 4.2 onto it. I pretty clearly made a mistake, as my car now thinks it is at 18% throttle position (checked with live feed obd2 reader) when I’m completely off the...
Hey guys,
I am new to the StangNet forums and I am helping a buddy work on his 1990 Mustang Foxbody 5.0. He purchased the car a couple of months ago and we have been working on this issue occasionally in the evenings.
Heres the problem: The car starts and drives fine, with no idling issues...
Hey mustang owners, pretty new to this community. Recently got a 2003 gt manual and it’s a pretty decent car I have been plans for it from a engine swap all the way to the suspension but that takes time and money so one step at a time.
i got the car when it had a spun bearing and 2 bent rods...
Hi everyone. I'm new to the Forums so I'm sure this question has been asked before but if you could help I would greatly appreciate it.
I recently picked up a 91 foxbody with a built 347 stroker. It runs great but I feel I can get more out of it. I took it to the track on street tires and...
Found this in my new fox. I’m not sure exactly what it is. The hose comes from under the intake manifold and back behind the engine I believe. Maybe I’m missing something here but I’ve never seen this..
I have the BBK valve covers and the hydro booster seems to be in the way. It looks like a process to remove it...anyone found a way to remove the covers without getting to deep into it? If I remove the hydro booster can I get away with out disconnecting any lines at all? Picture is what I’m...
What up Fellow Stang Owners!
Bought my SN95 a few months ago from my neighbor. May as well have stolen it from them for what I paid. Either way, the car was half dead and barely running. I've done a decent amount on it thus far (tune up, coolant flush, oil change, & rear drums and brake pads)...
Any help would be great. Bought a 1990 fox the motor had been swapped out of a 1995. All the 1990 top end and electrical was used. Car is not firing on 3 cylinder. Cylinder 2,4,and5 are not firing. New items are plugs,wires distributor, mas sensor,throttle sensor. Egr was deleted I have went...
Hey everyone,
bought a 96 Cobra. Looking to purchase headlights identical to these and have been searching all over for them but cannot find them. Can someone please help? I'll attach and image. If anyone can tell me the name, provide a link, anything! I would greatly appreciate it.
Thanks...
So I just finished rebuilding the TBI assembly on my 1985 Mustang 5.0 and the nut that screws into the back of the TBI assembly for the return fuel line has split in half. I cannot find replacement lines anywhere since it is the only year of TBI and I do not know what to do. It also seems that...