Ok. Been pondering if I sell this thing or not. I might…I might not. I have a number in my head I would let it go at, but want to see if it aligns with others. If not….i keep it for another year.
2000 GT 5-spd convertible.
72K miles. Black, with parchment top and interior.
No dash...
Hey folks,
any one got a good video of a 2000 / new edge mustang having the front cowl taken off and cleaned out?
I got a passenger side water leak, pretty sure condenser is clogged as no water exiting its lil spout noodle bit on the firewall
However i can't find a single video that actually...
I'll write this out as properly as I can, I'm suffering some electrical issues on a car I'm trying to "rescue".
2000 3.8L V6 Base Model, 180,000 km.
I've already fixed the misfires it had and got the engine running quite nicely, no CEL or anything.
Complaint:
Windshield wipers (VERY SELDOMLY)...
Kenne bell supercharged 2003 mustang GT 5 speed stick shift with black leather interior 103k miles.
-18" rovos wheels 275 fronts 295 rears
-Continental extreme contact tires with good tread
-1.5 inch eibach lowering springs
-AJE tubular k member and control arms
-2.1 intercooled kenne bell...
Hello.... I just wanted to introduce myself, my name is Rob, and I currently reside in Daly City, CA. I have a 2004 Mustang GT with a few bolt on mods,
-K&N cold air intake
-Flow Master cat back exhaust
-BBK Throttle Body Intake
-BAMA performance tuner
-MSD 2 valve Blaster coil packs
-BBK...
Hey all!
I have a 2002 Mustang GT 5 speed with 3.73 gears, a cold air intake, a 91 octane bama tune, an SLP loudmouth catback exhaust, and a throttle body. I really want to put in some cams but don’t know if I should have some supporting mods first. I was looking at stage 2 comp cams because it...
I've got a '99 v6 and I'm trying to make it something like the ultimate GT car, built solely being a driver's car. I don't want a lot of power, but I want fuel efficiency/emissions performance. Now, this may be a dumb question, but can I swap a police motor out of newer explorer that's crashed...
Today while driving a dead spot has developed in the center of my steering wheel mid-drive. My steering has had no issues whatsoever for the entirety of the time that I've owned this car (1999 Mustang GT). There's about a 1-2 inch dead zone in the steering where my wheel can turn but there is no...
Hey Guys - After many years, it's time for me to sell my baby. It's a 2002 Roush Stage 2, 5-speed. 194K miles. Just replaced a bunch of stuff (front struts, rear shocks, transmission mount, clutch cable, calipers all the way around, rotors all the way around, brakes all the way around). Stock...
so I recently replaced my power steering pump and now my belt is rubbing on a bolt between the crankshaft pulley and the power steering pump. the belt is routed correctly and I reused the old pulley. If anyone has suggestions or help it would be greatly appreciated
Hello everyone,
So I purchased a 2004 Mach 1 with 90,000 miles that needed some work about a month ago. I've been slowly working on my list of things to fix or repair on the car. It ran great when I took it for a test drive. Drove it for about an hour before I decided to take it home. I was...
I am currently looking to buy a New Edge Mustang to use as an autocross and/or rallycross car. My daily is a 2020 F-150 and I use FORScan to read diagnostics and programs things on there. Obviously, my truck's computer system is a "little bit" more complicated than the computers in the Mustangs...
How hard is it to drop a new long block 4.6l into a 2001 Mustang GT. I have some nasty bottom end rod knocks and just would rather put a new engine in myself. I know I'll need to get an engine cherry picker, and probably some new tools but I have a lot of tools available to me.
My question is...
Does this look like a ground? 2003 mustang GT. Replaced intake and now reverse lights,speedo, and blower motor is out. Could this have something to do with it? The wire is only about 5-6 inches long and literally nowhere to plug up. Any ideas?
I own a 2004 V6 mustang and am looking to do a coyote swap. I’m a student but working and willing to pay for the parts and labor. My plan is to buy a salvaged/wrecked 2011 gt, swap as much as i can from there and buy whatever else I need. I’ve priced everything out around 13k as i’ve already...
2002 Mustang GT Auto. Previous owner added a Dei 530T Module so the wiring is not orm from factory. I fixed the driver side power window and lock by re wiring everything back to stock. My problem is my passenger side is getting no power at all. Side Mirror and window do not work with any of the...
I've been having surging issues for a couple of months now. I replaced my IAC and checked for vacume leaks and tested my TPS. The surge is only slight. Maybe 25-50 rpm when its warm and on a real cold start it surges quite a bit for about a minute before smoothing out. I've done a reset and I've...
2004 gt, factory intake manifold, this bolt hole behind the throttle body towards the passenger side, goes into the plastic manifold, what's it for? Just wondering if somethings supposed to go there. (In the photo it's the hole with the brass sleeve there, between the TB spring and cable)
Well I've never posted on a forum , but im a bit confused
I have a 2000 v.6 automatic and recently I've replaced the wheel bearing on the front left tire
After awhile I went to drive it, and it started up just fine but when I shifted into reverse it started shaking from the front wheel area...
I'm new here but I have a 04 GT standard trans and my OEM plastic manifold broke at the heater hose fitting so I replaced it with a professional products typhoon intake manifold and I installed it and now the cars idle is very rough. Bouncing between 1200 rpms and 500 rpms. Thought it could be...