Hello everyone! I picked up a turbo for my SBF 347 stroker setup on a 1989 LX Foxbody. It's a single 76/74mm (I believe) Precision Turbo, 2x. 45mm Turbosmart wastegates & 1x. 50mm Turbosmart BoV.
I have a built motor with a standalone tunable ecu but its lacking a fuel system. It currently has...
YUCK, exhaust valves look beat to hell, cracks on exhaust seats on chambers 2 and 3 other possible reason for car being junked possibly caused by overheating and or clogged head gasket
YUCK, exhaust valves look beat to hell, cracks on exhaust seats on chambers 2 and 3 other possible reason for car being junked possibly caused by overheating and or clogged head gasket
Stock block 347 scat forged crank and rods, mahle flat top pistons,190cc twisted wedge, edelbrock pro flo 4 efi w/ 29lb injectors, walbro 255 fuel pump. 10.8:1 compression Would it be advisable to do a power adder with this setup? If not what should I change I am not looking to make a ton of...
I have an sandrail with a 99 3.8. The guy I bought it from said it was dynod at 197 hp. I am looking for a turbo kit. To add another 100-125 hp if possible on 91 octane. I am tearing the motor down for a full rebuild. I am a decent vw wrench. Many turbo vws. Just new to the 3.8.
Any...
Hello everyone. This will be the first time ive ever rebuilt an engine, I finally acquired all the necessary parts for it from piston rings to the fuel pumps. I wanted to see if there was a write up for the engine assembly potentially, if anyone had tips for me, as well as if there is somewhere...
Im currently trying to simplify the harness from the ecu(microsquirt) to the engine harness. But i have not had any luck finding the pin out information for the 16 pin connector for the engine harness. If anyone has any information on it it would be of great help
Hey Everyone
I was SUPER INSPIRED by the 1980 FOX AWD thread in this forum. I am a lifelong mustang owner. (First car was a black/ red 1983 Mustang GT T top, manual, 5.0L, bored .030 over, decked head, roller cam, MSD Ignition (6250rpm), full header, flow master, 8.8” ).
I am in the...
turbo 408w stroker, around 1200-1400 hp, trying to find help on an oiling/cooling system for my turbo setup. was thinking just an external dry sump system, one pump, and an oil cooler run thru that, but would also like an electric pump for pre-ignition priming. for intercooler, i was looking at...
Hi new to the page and in desperate need of some guidance.
I have a 89 fox 5.0 with an on3performance turbo set up and for the life of me cannot figure out my hot start issue. Car has 60lb injectors, 340lhp fuel pump, new high torque starter, new coolant temp sensor, new plugs, wires, cap...
Hello so I posted a while back and I decided to turbo my 4.6 2v with supporting mods and pushed around 420 Whp and now the motor is fried :( so I just bought another 2v motor with 84k miles I have sold some of the supporting mods like Bbk air intake, throttle body Etc. this build I want to...
93 mustang gt 302 5 speed. Currently I am running only the130 alternator/ water pump and crank. I bought an alternator bracket from amazon and removed the stock bracket with the tensioner. Now I’m also going to be converting to electronic fans. My issue is now, since my belt routing will be...
I’m building a a4 block with a 331 stroker mated to a t56 magnum plan on running a 4.10 gear with a 28” rear tire. my question is do u think a borg Warner s480 will keep me in boost with the manual trans or is there a better turbo for this application.