1965 Mustang rust repair

rusty428cj · Sep 8, 2011

Brian started the rust repair on the right sail panel and rear package tray

EP429 · Sep 8, 2011

Amazing work!

hungrymonkey · Sep 8, 2011

Impressive amount of work!

I didnt realize this until recently, but us mustang guys have it relatively easy when it comes to replacing huge amounts of sheet metal. Since we do not have to custom build many patches.

rusty428cj · Sep 8, 2011

Brian is starting to make a patch for the rocker

The rocker patch is finished and we starting lining up the left quarter and wheelhouse

66Coupe289POWER · Sep 8, 2011

May I ask where do you get the repair panels from and are they US made or overseas? Do you have to do any repair work to the panels?

Realmongo · Sep 8, 2011

Looking Good Rusty!

rusty428cj · Sep 9, 2011

66Coupe289POWER said:
May I ask where do you get the repair panels from and are they US made or overseas? Do you have to do any repair work to the panels?

CJ Pony Parts and I don't know of any sheetmetal made in the US. You have to test fit everything and make it fit your car.

rusty428cj · Sep 9, 2011

Brian is making patches for the right sail panel inner structure

Epoxy prime before the outer piece goes on

rusty428cj · Sep 12, 2011

Brian finished building the right sail panel inner structure today.

rusty428cj · Sep 16, 2011

Someone tried to remove the ignition switch by prying on it and ruined the opening so Brian cut it out

We replaced the dash in the 1965 fastback because of rust but the area around the switch was good.

After it was welded in and the welds ground down

rusty428cj · Sep 21, 2011

All the inner structure was sanded except the rear panel because of the braces and than epoxy primed

lil bull · Sep 22, 2011

dimension

Can u tell me where to get all the correct dimensions so when putting a 65 coupe back together I can make sure it is right and goes down the road as intended. right now the cowl is shot, the firewall the mostly gone as are the floors and floor supports. I have the diagram that is in the 65 Falcon/Mustang book but there are not enough of them to make sure it is correct. thanks.

rusty428cj · Sep 27, 2011

Getting ready to test fit the sheetmetal. The first thing we did was line up the wheelhouse using clamps and screws.

Than all the sheetmetal was test fitted and modified to fit (I forgot to take a picture) than taken off and the wheelhouse were welded.

Next step is to scuff everything so we can spray a coat of epoxy primer

65fastbackresto · Sep 28, 2011

I`m thinking when cars leave your shop

They are better then new. Your work is outstanding and I`m glad you share it with us, just watching your posts has kept me outta trouble several times.

robbz28 · Sep 28, 2011

65fastbackresto said:
They are better then new. Your work is outstanding and I`m glad you share it with us, just watching your posts has kept me outta trouble several times.

Rusty is the man....he's the Chuck Norris of mustang body men

rusty428cj · Sep 28, 2011

Now that it has been epoxy primed time to start installing the rear sheetmetal.

rusty428cj · Sep 29, 2011

We lined up all the rear sheetmetal as close as we could get it than set the roof on by lining it up where Brian drilled out the spot welds. We had to adjust the rear panel after test fitting the rear window moldings a little. It is quite a challenge trying to line up all this aftermarket sheetmetal that is NOT made like the original sheetmetal.

lil bull · Oct 5, 2011

Can u tell me where to get all the correct dimensions so when putting a 65 coupe back together I can make sure it is right and goes down the road as intended. right now the cowl is shot, the firewall the mostly gone as are the floors and floor supports. I have the diagram that is in the 65 Falcon/Mustang book but there are not enough of them to make sure it is correct. thanks.

rusty428cj · Oct 5, 2011

This is the only thing I have

We weld it to a cart before we cut anything out so the demensions will stay the same. You have to modify the parts to get the best fit you can.

rusty428cj · Oct 5, 2011

Brian has the quarters, rear panel and taillight panel installed

1965 Mustang rust repair

rusty428cj

Attachments

EP429

Member

hungrymonkey

White by Birth, Trash By Choice

rusty428cj

Attachments

66Coupe289POWER

Member

Realmongo

I prefer to be called "Evil Genius"

rusty428cj

rusty428cj

Attachments

rusty428cj

Attachments

rusty428cj

Attachments

rusty428cj

Attachments

lil bull

New Member

rusty428cj

Attachments

65fastbackresto

Active Member

robbz28

rusty428cj

Attachments

rusty428cj

lil bull

New Member

rusty428cj

rusty428cj

Similar threads

1965 Mustang rust repair

Attachments

Member

White by Birth, Trash By Choice

Attachments

Member

I prefer to be called "Evil Genius"

Attachments

Attachments

Attachments

Attachments

New Member

Attachments

Active Member

Attachments

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency