• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Electrical 1991 GT PCM Relay 4, 5 or six pins

  • Thread starter Thread starter Bamm
  • Start date Start date Oct 7, 2018
B

Bamm

New Member
Dec 20, 2014
3
0
1
Oct 7, 2018
#1
  • Oct 7, 2018
  • #1
Hello, everyone newbie here, I have a 1991 GT 5 SP, that starts, drives and has fuel pressure. Here is the problem while I'm driving the motor will just shut off, fuel pump will continue to run, electrical power to everything stay on, to restart I hav e to turn key all the way off and just restart and it will go for another 5 min or so. Also while just idling it will cut off about every 3 - 9 minutes.
The following is a list ov new part
starter
starter module
ignition switch
coil
fuel pump relay
rotor/ cap
plugs
plug wires
TFI
PIP
battery
PCM
Herre is where the PCM relay comes in it was not changes out, I pulled it (brown/black), it has four pins in it, but all the replacements has either five or six pins. Did one of my pins break off in the connection or should I continue to look for a four pin. If I should continue to look for a four pin can someone tell me where to purchase one.
Thank you

Oh yeah I'm 1800 dollars down from the repair shop in mustang still don't run right... again Thank you ...Army Strong!!!
 

Blown88GT

Founding Member
Nov 13, 1999
2,283
524
164
Palm Beach Gardens, FL
Oct 9, 2018
#2
  • Oct 9, 2018
  • #2
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 9, 2018
#3
  • Oct 9, 2018
  • #3
Fox body Mustangs are not the kind of car you choose if you have to pay someone else to fix it. I's time to start the DIY mechanic route.

To that end, here is some help...

Dump codes sticky

Look at the top of the 5.0 Tech forum where the sticky threads are posted. One of them is how to dump the computer codes. Codes may be present even if the CEL (Check Engine Light) isn’t on. You don’t need a code reader or scanner – all you need is a paper clip, or if your lady friend has a hair pin, that will do the job.
I highly suggest that you read it and follow the instructions to dump the codes. http://www.stangnet.com/mustang-forums/threads/how-to-pull-codes-from-eec4.889006/
 
You must log in or register to reply here.

Similar threads

T
Help with a 95 5L crank no start
  • TheBubbaJoe
  • Nov 4, 2025
  • 1994 - 1995 Specific Tech
Replies
3
Views
457
1994 - 1995 Specific Tech Nov 5, 2025
AeroCoupe
A
Resolved 1989 Mustang bogs down after 3-5 minutes of driving.
  • Alabama
  • Feb 11, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
2K
Fox 5.0 Mustang Tech May 26, 2025
limp
SURGING IDLE / NO IDLE CHECKLIST FOR 1999–2004 MUSTANG GT (4.6L 2V) - Work In Progress
  • Noobz347
  • Aug 30, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
927
1996 - 2004 SN95 Mustang -General/Talk- Aug 30, 2025
Noobz347
Resolved 1989 Mustang GT no spark, no trigger pump relay
  • Nine Finger Wrenching
  • Nov 26, 2023
  • Fox 5.0 Mustang Tech
Replies
14
Views
4K
Fox 5.0 Mustang Tech Nov 30, 2023
Nine Finger Wrenching
SURGING IDLE / NO IDLE CHECKLIST FOR 1996–1998 MUSTANG GT (4.6L 2V) - Work In Progress
  • Noobz347
  • Aug 30, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
751
1996 - 2004 SN95 Mustang -General/Talk- Aug 30, 2025
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?